Can-Am DS 450 X mx Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 152

background image

CONTROLS/INSTRUMENT/EQUIPMENTS

NOTE:

When selecting either ON with

headlights or ON without headlights,
the taillight will be on. On both ON po-
sitions, the lights will be on with the
engine running or not. Always turn the
ignition key to OFF position after en-
gine has been stopped.

7) Indicator Lamps

vmo2008-011-028_b

1. Neutral (N) indicator lamp
2. Check engine indicator lamp
3. Low fuel level indicator lamp

Transmission

is

in

neutral

position.

Lamp ON

(1)

:

Engine fault,

refer to

TROUBLESHOOTING

section or contact an authorized
Can-Am dealer.

Lamp blinks:

Engine is under

a protection mode (limp home),
contact an authorized Can-Am
dealer.

Low

fuel

level.

There

is

approximately

2.5 L

(.7 U.S. gal.) of fuel left in fuel
tank.

(1)

The lamp stays ON when the ignition
switch key and engine stop switch are
in running position and the engine is not
running.

8) Rear Brake Pedal

The rear brake pedal is located on the
RH side of the vehicle, in front of the
footpeg.

When pressed down, the rear brake
is applied. When released, it should
return to its original position.

vmo2008-011-012_a

1. Rear brake pedal

NOTE:

Braking effect is proportional

to the force applied on the lever and to
the type and condition of the terrain.

9) Transmission Lever

The transmission lever is located on
the LH side of the vehicle, in front of
the footpeg.

vmo2008-011-011_a

LH SIDE OF VEHICLE

1. Transmission lever

Refer to

SHIFTING THE TRANSMIS-

SION

in

OPERATING INSTRUCTIONS

section for more details.

_______________

61

«
...
61
62
63
64
65
...
»

Содержание DS 450 X mx

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 450 X mx

Бренд: LaTrax Страницы: 36

Бренд: Polaris Страницы: 118

1970 SKI-DADDLER

Бренд: AMF Страницы: 74

Бренд: Suzuki Страницы: 252

Бренд: Baja motorsports Страницы: 69

Бренд: Aeon Страницы: 196

Бренд: Can-Am Страницы: 147

eTiger ATV50S BLUE

Бренд: LAMAX Страницы: 150

Raider Max 175S

Бренд: Dazon Страницы: 54

Бренд: Polaris Страницы: 231

Бренд: TIMBCO Страницы: 36

Бренд: Sno Jet Страницы: 63

EASY FAST SMART

Бренд: Lovato Страницы: 26

Бренд: Kioti Страницы: 8

Бренд: Kioti Страницы: 178

POWERSPORTS AT125-B

Бренд: Coleman Страницы: 92

POWERSPORTS HS360ATV

Бренд: Coleman Страницы: 175

Бренд: Coleman Страницы: 185

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды