Can-Am DS 450 X mx Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 152

background image

MAINTENANCE PROCEDURES

For your convenience, a pressure
gauge is supplied in tool box.

TIRE PRESSURE

FRONT

REAR

MAXIMUM

69 kPa

(10 PSI)

62 kPa

(9 PSI)

Up to

100 kg

(220 lb)

MINIMUM

55 kPa

(8 PSI)

48 kPa

(7 PSI)

Although the tires are specifically de-
signed for off-road use, a flat may still
occur. Therefore, it is recommended
to carry a tire pump and a repair kit.

Tire/Wheel Condition

Check tire for damage and wear. Re-
place if necessary. Do not make a tire
rotation. The front and rear tires have
a different size.

WARNING

When the tires are replaced, never
install a bias tire with a radial tire.
This combined application may
create handling and/or stability
problems.
Do not mix tires of different size
and/or design on the same axle.
Front tire pairs or rear tire pairs
must be the identical model and
manufacturer.
For unidirectional tread pattern,
ensure that the tires are installed
in the correct direction of rotation.
The radial tires must be installed
as a complete set.

Wheel Removal

Loosen nuts then lift vehicle. Support
vehicle securely using jack stands. Re-
move nuts then remove wheel.

NOTICE

To avoid any damage to

front brake discs, never remove or
ride vehicle without front discs pro-
tectors properly installed.

vmo2008-011-103

DISC PROTECTOR

Wheel Installation

At front, ensure that brake discs pro-
tectors are properly installed.

vmo2008-011-104_a

FRONT WHEEL

1. Disc protector

Install nuts and washers (where appli-
cable).

WARNING

Install the tapered side on the nuts
towards rim.

110

______________

«
...
110
111
112
113
114
...
»

Содержание DS 450 X mx

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 450 X mx

Бренд: Yutrax Страницы: 10

Бренд: Rayco Страницы: 88

Бренд: KTM Страницы: 211

Бренд: E-Z-GO Страницы: 66

Бренд: Landoll Страницы: 62

Бренд: Taylor-Dunn Страницы: 206

Бренд: PRONAR Страницы: 133

Бренд: PRONAR Страницы: 136

Бренд: Arctic Cat Страницы: 59

Бренд: Arctic Cat Страницы: 80

Бренд: Arctic Cat Страницы: 84

Бренд: Arctic Cat Страницы: 64

Бренд: Arctic Cat Страницы: 118

Бренд: Arctic Cat Страницы: 60

Бренд: Arctic Cat Страницы: 119

Бренд: Arctic Cat Страницы: 76

Бренд: Arctic Cat Страницы: 130

Бренд: Arctic Cat Страницы: 131

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды