Can-Am DS 450 X mx Скачать руководство пользователя страница 113

Страница: 113 / 152

MAINTENANCE PROCEDURES

Gently tighten nuts in a criss-cross
sequence then apply a final torque of
52 N•m (38 lbf•ft).

NOTICE

Always use the recom-

mended wheel nuts and washers (if
applicable). Using a different nut
and washer could cause damages to
the rim.

Front Wheel Bearings

Front Wheel Bearings Inspection

Push and pull the wheels from the up-
per edge to feel the play. See an autho-
rized Can-Am dealer if there is any play.

Rear Axle

Rear Axle Inspection

Lift rear of vehicle high enough to have
wheels off the ground.

Push and pull rear axle to feel the play.

Look for axle bending or runout.

See an authorized Can-Am dealer if
there is any play or damage.

Suspensions

Suspension Inspection

Shock Absorbers

Inspect shock absorber for oil leaks and
fasteners for tightness. See an autho-
rized Can-Am dealer if necessary.

WARNING

– Shock absorbers are pressur-

ized.

– An explosion may occur if

heated or punctured.

– Do not disassemble.

Suspension Arms, Swing Arm and
Linkage Inspection

Check

these

parts

for

damages

(cracks, dents, excessive play or cor-
rosion pin-holes). If one of these dam-
ages is detected

DO NOT USE THE

VEHICLE AND SEE AN AUTHO-
RIZED CAN-AM DEALER.

WARNING

Never ride a vehicle with a defec-
tive suspension parts.

Front Suspension Lubrication

Lubricate front suspension lower arms
with a grease gun. Use SUSPENSION
GREASE (P/N 293 550 033) or an equiv-
alent.

vmo2008-011-054_a

TYPICAL — LOWER SUSPENSION ARM

1. Grease fittings

Rear Suspension Lubrication

Lubricate with SUSPENSION GREASE
(P/N 293 550 033) at grease fittings
shown.

______________

111

Содержание DS 450 X mx

























































































































































Результаты поиска

Содержание DS 450 X mx

Отзывы:

Похожие инструкции для DS 450 X mx

Бренды по названию

Популярные бренды

Can-Am DS 450 X mx, Руководство оператора

Результаты поиска

Содержание DS 450 X mx

Отзывы:

Похожие инструкции для DS 450 X mx

Бренды по названию

Популярные бренды