Can-Am DS 450 X mx Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 152

background image

OPERATING INSTRUCTIONS

vmo2008-011-038_b

Release button immediately when en-
gine has started.

vmo2008-011-038_c

WARNING

Do not apply throttle while start-
ing.

Shifting the Transmission

Gearshift Control

To shift the transmission, pull in the
clutch lever, then operate transmis-
sion lever as follows.

WARNING

Always use the clutch lever to up-
shift or downshift.

One full stroke of the pedal shifts the
transmission to the next higher or
lower gear in the shifting sequence.
The pedal should automatically return
to its original position.

To upshift to a higher gear, put the end
of your boot under gearshift lever and
lift up the pedal one full stroke. To
downshift, lean the tip of the trans-
mission lever and depress pedal one
full stroke.

vmo2008-011-019_g

WARNING

Always release the throttle when
shifting gears. Shifting gears with-
out releasing the throttle, could
cause loss of control or cause the
vehicle to overturn.

NOTICE

Make sure parking brake

is fully disengaged before operating
vehicle.

Stopping the Engine

WARNING

Avoid parking vehicle on slope.

Release throttle and completely stop
the vehicle.

_______________

67

«
...
67
68
69
70
71
...
»

Содержание DS 450 X mx

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 450 X mx

Бренд: Suzuki Страницы: 111

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 76

Бренд: Yutrax Страницы: 8

Бренд: Yamaha Страницы: 3

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 73

WOLVERINE YFM35XV

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 136

Бренд: Yamaha Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды