Can-Am DS 450 X mx Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 152

background image

MAINTENANCE PROCEDURES

This section includes instructions for
basic maintenance procedures. If you
have the necessary mechanical skills
and the required tools, you can per-
form these procedures. If not, see
your authorized Can-Am dealer.

Other important items in the mainte-
nance schedule that are more difficult
and require special tools are best per-
formed by your authorized Can-Am
dealer.

WARNING

Turn off the engine and follow
these

maintenance

procedures

when performing maintenance.
If you do not follow proper main-
tenance procedures you can be
injured by hot parts, moving parts,
electricity, chemicals or other haz-
ards.

WARNING

Should removal of a locking de-
vice (e.g. lock tabs, self-locking
fasteners, etc.) be required when
undergoing

disassembly/assem-

bly, always replace with a new one.

Engine Oil

Engine Oil Level

The engine oil tank is located in front of
engine.

NOTICE

Check

level

frequently

and refill if necessary. Do not over-
fill. Operating the engine with an
improper level may severely dam-
age engine/transmission. Wipe off
any spillage.

NOTE:

While checking the oil level, vi-

sually inspect oil tank and engine area
for leaks.

vmo2008-011-014_a

LH SIDE OF VEHICLE

1. Oil tank dipstick

With vehicle on a level surface, start
engine and let it running at idle, around
1 minute, then stop engine. Check oil
level as follows:
1. Unscrew dipstick and wipe clean.
2. Screw dipstick until it bottoms.
3. Remove dipstick and check oil

level. It should be near or equal
to the upper mark.

vmo2008-011-017_a

1. Full
2. Add
3. Operating range

To add oil, remove the dipstick. Place a
funnel into the oil tank fill hole to avoid
spillage.

Add a small amount of oil and recheck
oil level.

Repeat the operation until oil level
reaches the dipstick’s upper mark.

Do

not overfill.

Properly tighten dipstick.

_______________

87

«
...
87
88
89
90
91
...
»

Содержание DS 450 X mx

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS 450 X mx

Бренд: Bajaj Motorsport Страницы: 8

2002/24 ATV-300XS

Бренд: HER CHEE Страницы: 56

Бренд: VANDERHALL Страницы: 109

Бренд: Land Pride Страницы: 132

650 MUD PRO 2011

Бренд: Arctic Cat Страницы: 84

Бренд: Eton Страницы: 30

Бренд: Can-Am Страницы: 401

Бренд: Strongway Страницы: 16

DS 450 EFI X mx

Бренд: Can-Am Страницы: 156

amphibious, off-road utility vehicle

Бренд: Centaur Страницы: 56

Sportsman 90 2011

Бренд: Polaris Страницы: 12

RECOIL iS CREW 2015

Бренд: Bad Boy Страницы: 60

Бренд: FARMA Страницы: 13

Magnum 500 2000

Бренд: Polaris Страницы: 5

Бренд: Polaris Страницы: 13

600 IQ Widetrak

Бренд: Polaris Страницы: 140

2008 Scrambler 500 2X4 International

Бренд: Polaris Страницы: 124

Supersport 2007

Бренд: Polaris Страницы: 266

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды