Can-Am DS 450 X mx Скачать руководство пользователя страница 92

Страница: 92 / 152

MAINTENANCE PROCEDURES

NOTICE

Take care not to damage

O-ring while inserting outlet fitting
into oil tank. Apply oil on O-ring to
ease installation.

vmo2008-011-100_a

OIL OUTLET ASSEMBLY

1. Hexagonal bolt
2. Washer
3. Insert
4. Outlet fitting
5. O-ring
6. Strainer

Oil Filter Replacement

Unscrew oil filter cover.

NOTE:

Remember screws location.

vmo2008-011-042_a

LH SIDE OF ENGINE

1. Oil filter cover
2. Screw (M6 x 25)
3. Screw (M6 x 55)

Remove the oil filter and replace by a
new one.

NOTE:

Check and change the O-ring, if

necessary.

vmo2008-011-084_a

LH SIDE OF ENGINE

1. Oil filter cover
2. Oil filter
3. O-ring

Wipe off any oil spillage on engine.

Change gasket on drain plugs. Clean
gasket area on engine, oil tank and
drain plugs then reinstall plugs.

Refill

oil

tank

with

1.8 L

(1.9 qt (U.S. liq.)) of the recommended
oil. Refer to

RECOMMENDED EN-

GINE OIL

in this section for more

details.

Start engine and let idle for a few min-
utes.

Ensure there are no leaks.

Stop engine and check oil level. Refill if
necessary.

Dispose oil as per your local environ-
mental regulations.

Engine Coolant

Engine Coolant Level

WARNING

Check coolant level with engine
cold. Never add coolant in cooling
system when engine is hot.

______________

Содержание DS 450 X mx

























































































































































Результаты поиска

Содержание DS 450 X mx

Отзывы:

Похожие инструкции для DS 450 X mx

Бренды по названию

Популярные бренды

Can-Am DS 450 X mx, Руководство оператора

Результаты поиска

Содержание DS 450 X mx

Отзывы:

Похожие инструкции для DS 450 X mx

Бренды по названию

Популярные бренды