![background image](http://html1.mh-extra.com/html/california-instruments/fcs-series-ii/fcs-series-ii_user-manual_3475047098.webp)
User Manual – Rev B
FCS Series II
6.3.1 Measurement Cal - AC
AC
m the output voltage to maximum voltage on the high
which may take several minutes. Once completed, the new cal
AC
tput relay and switch to the low voltage range.
Apply load as indicated in Table 6-1 and close output relay
revent a current li
t the unit to the
rrent mode. With
ing, this should
ary ho
gram the output to bout 80%
scale v
e on the low volta range and
400 Hz. Observe the actual output current on the reference
DMM and enter this current reading value in the MCURR FS
parameter field. Press the ENTER key. Wait for the calibration
inutes. Once
completed, the new cal factor will be displayed. If the auto-cal
process is unable to complete successfully, the original cal
factor will be displayed instead. This can happen if the meter
reading was entered incorrectly.
6.3.2 Single and Three Phase Modes
Volt Full-scale:
Progra
voltage range and 400 Hz. Close the output relay. Go to the
MEASUREMENT CALIBRATION screen. Enter the actual AC
output voltage reading in the MVOLT FS parameter field, then
press the ENTER key. Wait for the calibration cycle to finish,
factor will be displayed. If the auto-cal process is unable to
complete successfully, the original cal factor will be displayed
instead. This can happen if the meter reading was entered
incorrectly.
Current Full-scale:
Open the ou
again. To p
constant cu
not be necess
to
of full-
mit fault, you can se
the correct load sett
wever. Pro
olta
ang
a
90%
ge r
ge
cycle to finish, which may take several m
As indicated earlier, for 3-Phase power system, repeat the preceding steps for the Phase B and
C outputs. The order in which the outputs for each phase are calibrated is not important.
Press the PHASE key to select each output to be calibrated. Monitor the output of the
respective phase by moving the HI input of the Digital Multimeter and the current shunt as
needed. The LO input should remain connected to the common LO of the sense connector.
The current measurement calibration for Phase A (ø1) should be done in both single and three
phase modes as separate calibration coefficients apply to each phase mode. Voltage
measurement calibration for phase A (ø1) can be done in either phase mode.
California Instruments
98
Содержание FCS Series II
