![background image](http://html1.mh-extra.com/html/california-instruments/fcs-series-ii/fcs-series-ii_user-manual_3475047203.webp)
User Manual – Rev B
FCS Series II
Number
Message String
Cause
Remedy
-168
"Block data not allowed"
as sent.
Check programming manual for
correct command syntax
Block data w
-200
"Execution error"
Command may be inconsistent with
mode of operation.
Command could not
be executed
-201
"Invalid while in local"
ued but
remote
Command iss
unit is not in
state
Put instrument in remote state before
issuing GPIB commands.
-203
"Command protected"
Command is locked
ands are supported by
out
Some comm
the unit but are locked out for
protection of settings and are not user
accessible.
-210
Problem with trigger
system.
for
ment.
"Trigger error"
Unit could not generate trigger
transient execution or measure
-211
"Trigger ignored"
Trigger request has
been ignored.
Trigger setup incorrect or unit was not
armed when trigger was received.
Check transient system or
measurement trigger system settings.
-213
but
"Init ignored"
Initialization request
has been ignored
Unit was told to go to armed state
was unable to do so. Could be
caused by incorrect transient system
or measurement acquisition setup.
-220
Parameter not
allowed.
value. Check programming manual
for allowable parameters
"Parameter error"
Incorrect parameter or parameter
-221
"Setting conflict"
programmed with
Check other settings. E.g. Redefine
transient mode.
or
waveform not set to Sine.
Transient
more than 1 mode.
As result of *TST? execution,
indicates ALC mode is off
-222
"Data out of range"
r data
Check programming manual for
Paramete
outside of allowable
range.
allowable parameter values
-223
"Too much data"
a received
More dat
than expected
Check programming manual for
number of parameters or data block
size
-224
"Illegal parameter value"
Parameter value is
not suppored
Check programming manual for
correct parameters
-226
"Lists not same length"
One or more transient
lists programmed has
different length.
or
nd
All lists must be of same length
transient cannot be compiled a
executed.
-241
"Hardware missing"
N/A
N/A
-254
ll"
eft
or data to make
room.
"Media fu
No storage space l
to save settings or
data.
Delete other settings
-255
ry entries
Delete one or more waveforms from
waveform memory to make room.
“Directory full”
Too many waveform
directo
-256
“File name not found”
Waveform requested
not in directory
waveform names present.
Check waveform directory for
-257
Incorrect filename
“File name error”
Too many or non ASCII characters
used in waveform file definition.
-283
“Illegal variable name”
Variable name illegal.
nly
Use ASCII characters o
California Instruments
203
Содержание FCS Series II
