Cabletron Systems SmartSwitch 9W006 Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 284

background image

USER’S GUIDE

250 SmartSwitch Remote Access Module

ipxBasicSysInDiscards

The number of IPX packets received but discarded due to reasons other than those accounted for
by ipxBasicSysInHdrErrors, ipxBasicSysInUnknownSockets, ipxAdvSysInDiscards, and
ipxAdvSysInCompressDiscards.

ipxBasicSysInBadChecksums

The number of IPX packets received with incorrect checksums.

ipxBasicSysInDelivers

The total number of IPX packets delivered locally including packets from local applications.

ipxBasicSysNoRoutes

The number of times no route to a destination was found.

ipxBasicSysOutRequests

The number of IPX packets supplied locally for transmission, not including any packets counted in
ipxAdvForwPackets.

ipxBasicSysOutMalformedRequests

The number of IPX packets supplied locally that contained errors in their structure.

ipxBasicSysOutDiscards

The number of outgoing IPX packets discarded due to reasons other than those accounted for in
ipxBasicSysOutMalformedRequests, ipxAdvSysOutFiltered and
ipxAdvSysOutCompressDiscards.

ipxBasicSysOutPackets

The total number of IPX packets transmitted.

ipxBasicSysConfigSockets

The configured maximum number of IPX sockets that may be open at one time.

ipxBasicSysOpenSocketFails

The number of IPX socket open calls which failed.

IPX A

DVANCED

S

YSTEM

T

ABLE

S

TATISTICS

ipxAdvSysMaxPathSplits

The maximum number of paths with equal routing metric value which this instance of the IPX may
split between when forwarding packets.

ipxAdvSysMaxHops

The maximum number of hops a packet may take.

ipxAdvSysInTooManyHops

The number of IPX packets discarded due to exceeding the maximum hop count.

ipxAdvSysInFiltered

The number of incoming IPX packets discarded due to filtering.

«
...
248
249
250
251
252
...
»

Содержание SmartSwitch 9W006





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartSwitch 9W006

Бренд: D-Link Страницы: 61

LTE Mobile HotSpot PRO

Бренд: Samsung Страницы: 77

Бренд: macaroon Страницы: 13

Бренд: Cambium Networks Страницы: 196

Бренд: Cambium Networks Страницы: 478

Бренд: Cambium Страницы: 301

Бренд: Cambium Networks Страницы: 287

Бренд: H3C Страницы: 37

Бренд: H3C Страницы: 41

Бренд: Ebyte Страницы: 10

Бренд: Airlink101 Страницы: 56

NUCLIAS CONNECT DAP-2680

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 25

Бренд: D-Link Страницы: 26

nuclias connect DAP-2662

Бренд: D-Link Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды