Bticino MH08CT/GB, Техническое руководство

Страница: 75 / 156

MY HOME cOntROL technical GUiDe
73
configurAtion
Operating mode with SPE = 7
This mode can perform the controls envisaged by the Basic operating mode with
SPE = no configurator when NC (normally closed) pushbuttons or switches are
connected to the interface terminals.
3) Example of configuration:
If you want to call scenario 3 of module item F420 with a traditional connected
pushbutton contact PL1 or N1, you must configure SPE=4 and M=3.
In positions A and PL1 you must configure the address of the scenario module
F420 to be controlled with the traditional pushbutton (for example A=1 and
PL1=1 for the unit with address A=1 and PL=1).
1) Device to be combined with an OFF control for switching off. The flash time is
indicated in the table:
Configurator Time (seconds)
none 0.5
1 1
2 1.5
3 2
4 2.5
5 3
6 3.5
7 4
8 4.5
9 5
2) Device to be combined with the dimmer actuator and an OFF control for switching
off. The configurator defines the adjustment in % of the load power.
Configurator
% of load
1 10
2 20
3 30
4 40
5 50
6 60
7 70
8 80
9 90
T T
4) M=1 to 8: group of scenarios to be controlled with the 4 keys:
M First contact (PL1) Second contact (PL2)
1 1 2
2 3 4
3 5 6
4 7 8
5 9 10
6 11 12
7 13 14
8 15 16
Room (A) and Light point (LP):
A=0 to 9 and PL1=1 to 9 are the room and the light point of the scenario
module to be controlled.
PL2 must be the same as PL1, or not configured (in this case the second
contact is disabled).
The functioning mode is the same as the control item H/L5651/2, item
AM5831/2 and scenario control item HC/HS/L/N/NT4680:
- short contact closing (less than 3 seconds) scenario activation
- long contact closing (from 3 to 8 seconds) programming start
- long contact closing (more than 8 seconds) cancellation
- when programming, the LED flashes slowly
- when cancellation is confirmed, the LED will start flashing quickly for 4
seconds.
If position PL2 is configured as well (e.g. with configurator 2), the interface is
enabled to repeat scenario 3 of a second scenario module with address A=1
and PL=2 with a traditional pushbutton connected to contact PL2 or N2.
If positions PL1 and PL2 instead have the same configurator, both pushbuttons
connected to the interface repeat scenario 3.
Instead two different scenarios of the same module cannot be controlled with
one interface.
Whenever only a traditional device is to be connected to the interface, this
must be connected only to contact PL1 or N1 and positions A and PL1 must be
configured.
Advanced operating mode
If position SPE is correctly configured as well as position M the device
performs special functions listed in the table below.
Operating functions possible with configurator in position SPE
Possible function Configurator Value configurator in
M
in position
SPE
single function double function
Locks the state of the devices to which the control is addressed 1 1 —
Unlocks the state of the devices to which the control is addressed 1 2 —
Unlocks with key connected in PL2 or N1 (item F428) 1 — 3
and locks with key connected in PL1 or N2 (item F428)
On with flash
1)
2 none to 9 —
ON (key in PL2 or N1 for item F428) - OFF (key in PL1 or N2 1 — 0/I
for item F428) without adjustment
cyclical ON/OFF without adjustment
1 7 —
(only NO contact)
Selection adjustment level fixed at 10 to 90 % of the dimmer 2) 3 1 to 9 —
Call the scenarios of module F420 4 1 to 4 —
whose address is specified in A and PL 3)
Management of scenario module item F420 5) 6 (see table in the following page)
ON timed (2 seconds) 8 1
ON timed (10 minutes) 8 2
PL1
A1
M
SPE
AUX
PL
A
L4651/2
M
SPE
AUX
PL
A
PL1
A1
A2
PL2
M
A3
PL3
L4652/3
L/N4681
PL
A
M
M
G1
G2
PL
A
L4671/1
M
G
PL
A
L4671/2
L/N4688
SPE
PL2
M
PL1
A1
SPE
PL2
M
position SPE