Bruker minispec mq20 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 86

Bruker minispec mq20 Скачать руководство пользователя страница 19

Technical Data

E1400912_1_001

19

4

Technical Data

4.1

General Information

No.

Series

Type

Weight

(kg)

Length

(cm)

Width

(cm)

Heigth

(cm)

1

mq20

Toothpaste
Analyzer

105

65

75

33

Table 4.1: Technical Data: General Information

All specifications above are without a PC. Weights and dimensions apply to the instruments,
not to the packaged systems.

4.2

Connection Values

Grounding is vital for the safe operation of the instrument. Never operate with the grounding
conductor disconnected. If the local wiring does not provide a ground, an earth-to-chassis
connection must be added at the user’s location.

Note

: Since the input voltage may be unstable in a laboratory environment, it is

recommended to connect the minispec to a separate circuit that is not used by any other
equipment. Furthermore, a voltage stabilizer or UPS may be required to avoid instrument
instabilities or other unexpected system behavior caused by a fluctuating input voltage.

No.

Series

Type

ND/NE/NF

Voltage/VAC

Apparent
Power
Consumption,
Maximum/VA

Circuit
Protection
(Two
indications:
NF/ND Series)

Freque
ncy/Hz

1

mq20

Toothpaste
Analyzer

NF

100-240

300/250

3.15/2.5 AT (2
pieces)

50-60

Table 4.2: Electrical Connection Values

«
...
17
18
19
20
21
...
»

Содержание minispec mq20























































































Отзывы:

Нет отзывов