Broadcom NetXtreme/NetLink BCM5717 Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 593

background image

Initialization Procedure

BCM5718 Programmer’s Guide

Broadcom

®

January 29, 2016 • 5718-PG108-R

Page 140

This step is relevant when TCP/UDP checksum calculations are offloaded to the device. The device driver
may optionally disable receive and transmit pseudo header checksum calculations by the device by setting
the Receive_No_PseudoHeader_Checksum and Send_No_PseudoHeader_Checksum bits in the General
Mode Control register (see

“Mode Control Register (Offset 0x6800)”

). If the

Send_No_PsuedoHeader_Checksum bit is set, the host software must seed the correct pseudo header
checksum value in TCP/UDP checksum field. Similarly, if the Receive_No_PsuedoHeader_Checksum bit is
set, the device driver must calculate the pseudo header checksum and add it to the TCP/UDP checksum
field of the received packet.

11.

Configure MAC Mbuf memory pool watermarks (

“MAC RX MBUF Low Watermark Register (offset: 0x4414)”

“Read DMA MBUF High Watermark Register (offset: 0x4418)” on page 430

). Broadcom

has run hardware simulations on the Mbuf usage and strongly recommends the settings shown in

These settings/values establish proper operation for 10/100/1000 speeds.

12.

Configure flow control behavior when the Rx Mbuf low watermark level has been reached (see

13.

Enable the buffer manager by setting the Enable and Attn_Enable bits in the Buffer Manager Mode register
(see

“Buffer Manager Mode Register (offset: 0x4400)” on page 428

). The buffer manager handles the

internal allocation of memory resources for send and receive traffic.

14.

Set the BD Ring Replenish threshold for the RX Producer Ring. The threshold values indicate the number
of buffer descriptors that must be indicated by the host software before a DMA is initiated to fetch additional
receive descriptors in order to replenish used receive descriptors. The recommended configuration value for
the standard receive BD Ring replenish threshold is 0x19 (see

“Standard Receive BD Producer Ring

Replenish Threshold Register (offset: 0x2C18)” on page 373

15.

Initialize the standard receive Buffer Ring. Host software must write the Ring Control Block structure (see

“Ring Control Block” on page 107

) to the standard receive BD Ring RCB register (see

“Standard Receive

BD Ring RCB Registers” on page 366”

). Host software must initialize the host physical memory address

based on allocation routines specific to the OS.

16.

Initialize the Max_len/Flags Receive Ring RCB register (0x2458).

Table 38: Recommended BCM57XX Ethernet Controller Memory Pool Watermark Settings

Register

Standard Ethernet Frames

MAC RX Mbuf Low Watermark (0x4414)

0x2A

Mbuf High Watermark (0x4418)

0xA0

Note:

The Low WaterMark Max Receive Frames register (0x504) specifies the number of good frames to

receive after RxMbuf Low Watermark has been reached. The driver software must make sure that the MAC

RxMbuf Low WaterMark is greater than the number of Mbufs required for receiving the number of frames as

specified in 0x504. The first Mbuf in the Mbuf chain of a frame will have 80 bytes of packet data while each of

the subsequent Mbufs [except the last Mbuf] will have 120 bytes for packet data. The last Mbuf in the chain will

have the rest of the packet data which can be up to 120 bytes.

Table 39: Recommended BCM57XX Ethernet controller Low Watermark Maximum Receive Frames

Settings

Register

Recommended Value

Low Water Mark Maximum Receive Frames

(0x504)

1

«
...
138
139
140
141
142
...
»

Содержание NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NetXtreme/NetLink BCM5717

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 36

Бренд: RADEMACHER Страницы: 68

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: IBA Страницы: 29

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: Danfoss Страницы: 2

Бренд: Procom Страницы: 10

Бренд: Whale Страницы: 8

Бренд: Tascam Страницы: 8

Бренд: Ashly Страницы: 1

Бренд: OneFex Страницы: 24

Бренд: Lampert Страницы: 15

Бренд: Vent-Axia Страницы: 4

Бренд: Waterbird Страницы: 19

963321-0403 - Cordless Precision Controller

Бренд: Logitech Страницы: 1

MOBA-Matic MMC-1000

Бренд: MOBA Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды