Broadcom NetXtreme/NetLink BCM5717 Скачать руководство пользователя страница 323

Страница: 323 / 593

Ethernet MAC (EMAC) Registers

BCM5718 Programmer’s Guide

Broadcom

January 29, 2016 • 5718-PG108-R

Page 323

RSS IPV4 Hash Enable

When this bit is set, 2-tuple hashes are enabled

for IPV4 packets.

Reserved

15:13

–

FIX EMAC drops a packets if

incoming DA partial match

both perfect and Pause

Multicast address

This bit disables the fix that EMAC stage fsm

drops a packet if incoming packet's DA has a

partial match in both perfect match address and

Pause Multicast address.

Filter Broadcast

When set, reception of broadcast frames is

disabled

Keep VLAN Tag Diag mode

If set, forces Receive MAC to keep the VLAN tag

in the frame.
This is for debugging purpose only and should be

reset during normal operation

No CRC Check

When set, no CRC check by receive MAC on

incoming frames.
Also, allows the reception of packets received

with RXERR on MII/GMII.

Promiscuous mode

When set, no source address or MC hashing

checking will be performed on incoming frames.
All frames will be accepted.

Length Check

If set, 802.2 length checking is done on LLC

frames.

Accept Runts

If set, MAC accepts packets less than 64 bytes.

Reserved

–

Keep Pause

If set, MAC forwards pause frame to host buffer.

Reserved

–

Enable Flow Control

Enable automatic processing of 802.3x flow

control frames.
This bit is orthogonal to the Keep Pause bit.

Enable

This bit controls whether the Receive MAC state

machine is active or not.
When set to 0, it completes the current operation

and cleanly halts. Until it is completely halted, it

remains 1 when read.

Reset

When this bit is set to 1, the Receive MAC state

machine will be reset.
This is a self-clearing bit.

Name

Bits

Access

Default
Value

Description

Содержание NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NetXtreme/NetLink BCM5717

Отзывы:

Похожие инструкции для NetXtreme/NetLink BCM5717

Бренды по названию

Популярные бренды

Broadcom NetXtreme/NetLink BCM5717, Руководство программиста

Результаты поиска

Содержание NetXtreme/NetLink BCM5717

Отзывы:

Похожие инструкции для NetXtreme/NetLink BCM5717

Бренды по названию

Популярные бренды