Bradley FLOAT Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 20

background image

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

bradleycorp.com

AD3-FLOAT_Install Rev. A

© 2021 Bradley

Page 1 of 20

12/10/2021

Euro Style Restroom Partitions

Phenolic LT – FLOAT Series

Table of Contents

Safety Information   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Supplies Required  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Marking & Installing U-Brackets .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Making Notches (if necessary)   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Installing U-Bracket on Middle Pilasters   .  .  .  .  .  .  .  .  .  . 6
Mounting Middle Pilaster to Partition Panel .  .  .  .  .  .  .  . 7
Assembling the Feet   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Mounting the Wall Brackets  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10
Installing Middle Panel & Side Panel .  .  .  .  .  .  .  .  .  .  .  . 11
Installing Headrail   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12
Installing Doors   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Aligning the System  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Pre-Drilling the System   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 14
Mounting Headrail   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 15
Riveting Wall Connections  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 16
Mounting Door Latches   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 17
Mounting Hooks & Bumpers   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 18
Appendix A: LED Occupancy Indicator   .  .  .  .  .  .  .  .  .  . 20

Read the instructions in this manual before beginning installation. Save these instructions

and refer to them for inspection, maintenance, and troubleshooting information.

For questions regarding the operation, installation or maintenance of this product, visit bradleycorp .com
or call 800 .BRADLEY (800 .272 .3539) .

Product warranties and parts information may also be found under “Resources” on our website at bradleycorp .com .

1
2
3
...
»

Содержание FLOAT Series





















Отзывы:

Нет отзывов

Похожие инструкции для FLOAT Series

Бренд: Garden Treasures Страницы: 6

Бренд: ABSCO SHEDS Страницы: 14

Бренд: Palmako Страницы: 8

Бренд: Furinno Страницы: 4

Бренд: Next Страницы: 16

Бренд: Triarch Страницы: 1

Бренд: real living Страницы: 8

Бренд: GALA MEBLE Страницы: 13

Бренд: Garden Treasures Страницы: 5

Бренд: Tech Craft Страницы: 7

BASIC 3DV nadstavec

Бренд: avaks nabytok Страницы: 4

AXFRYLE 804.423.96

Бренд: IKEA Страницы: 5

Бренд: Klaxon Страницы: 2

Бренд: rst brands Страницы: 16

Бренд: Garden Winds Страницы: 6

Бренд: C&T International Страницы: 3

Бренд: YOTRIO Страницы: 16

Бренд: Seconique Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды