Bradley Bradmar 400 Series, Руководство по установке

Страница: 15 / 21

15
Installation
Bradmar
™
Restroom Partitions, Floor-Mounted with Overhead Brace — Series 400
Bradley
•
HDWP-INSTR-013 Rev. K; ECN 12-14-012 10/1/2014
9 Latch and Strike/Keeper for Inswing Doors
Local codes vary from state to state. Check your local
codes before installing the coat hook and door pulls.
D
C
Line up the center hole of the strike/keeper with the mark on
the pilaster . Using the strike/keeper as a template, drill Ø ¼"
holes through the pilaster . It is not necessary to remove the
strike/keeper before drilling. Secure the strike/keeper to the
pilaster using hardware provided .
E
For 32"-26" (813mm–914mm) ADA doors, measure 5½"
(140mm) from the latched side of the door and 25¾" down
from the top of the door . Drill Ø ¼" hole through the face of
the door. Drill an identical hole, 3½" (89mm) below the hole
just drilled . Install one door pull to each side of the door with
the hardware provided .
Using the latch mounting holes as a template, drill a Ø
⁷⁄₃₂
"
pilot hole into the door, ¾" (19mm) deep. Secure the latch to
the door using hardware provided .
A
B
F
G
With the door in the closed position, set
the latch on the inside of the door so that
the slide bar is centered in the slot on the
strike/keeper . The leading edge of the
latch should be positioned approximately
³⁄₈
" (10mm) from the door edge.
Install the coat hook in the upper corner on
the inside of the door on the latched side
at a location 3" (76mm) down from the top
and 3" (76mm) in from the side. Using the
coat hook as a template, drill two Ø
⁵⁄₃₂
"
pilot holes (max. ¾" [19mm] deep). Secure
the coat hook using hardware provided .
Repeat steps A-F for remaining doors .
The measurement from the top of the door to the
center hole on the strike/keeper is 27½" (699mm).
Mark this measurement on the inside of the pilaster,
opposite the hinged side of the door .
25¾"
(654mm)
5½"
(140mm)
³⁄₈
"
(10mm)
27½"
(699mm)
3½" (89mm)
Door
Latch
Pilaster
One Ear Door
Stop (Inswing)
Flat Door Stop
(Inswing)
#10-24 x ¾" Machine Screw
#14 x ¾" Screw
#10 x ¾"
Screw
3" (76mm)
3" (76mm)
Coat Hook
(Inswing)
#14 x ¾" Screw
#14 x ¾" Flat Head Screw
#14 x ¾" Screw
#10-24 x 2" Machine Screw
Door Pull
Door Pull
Slide
Latch
Slide
Latch
FLAT DOOR
STOP
ONE EAR
DOOR STOP
Door Pull
Door Stop (Inswing)
#10-24 x ¾" Barrel Nut
#14 x ¾" Screw
#10-24 x 2"
Machine Screw
Slide
Latch
Door Pull w/
Countersink (added for
32"-36" inswing ADA
Doors)
#10-24 x ¾"
Shoulder Screw
DOOR STOP
Door Pull w/
Countersink (added
for 32"-36" inswing
ADA Doors)
Door Pull w/
Countersink (added
for 32"-36" inswing
ADA Doors)