Bosch VG5 600 Series Скачать руководство пользователя

Страница: 15 / 88

AutoDome 600 Series Analog PTZ Camera

Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en

Bosch Security Systems, Inc.

Installation Manual

F.01U.265.793 | 2.0 | 2012.02

Purchase the appropriate mounting hardware to use, depending on the location of the

AutoDome, either wall mount, corner mount, or mast (pole) mount.

If you application contains a Power Supply Box, refer to

Section 2.3 Mount Power Supply

Box, page 15

If you are using the Mounting Plate with a 24 V VG5 AutoDome, refer to

Section 2.8 Installing the VG4-A-ARMPLATE, page 27

2.3

Mount Power Supply Box

Before mounting the Power Supply Box decide if you should wire the box through the holes in

the bottom or back of the box. If wiring the box through the back, move the two (2) seal plugs

to the bottom through the holes before mounting.

Figure 2.1

Power Supply Wall, Mast (Pole), and Corner Mounts

Use the wall mount template supplied in the packaging box to locate the four (4)

mounting holes for the Power Supply Box.

Drill four (4) holes for the mounting anchors. If installing outdoors, apply a weatherproof

sealant around each hole at the mounting surface.

CAUTION!

Select a rigid mounting location to prevent excessive vibration to the AutoDome camera.

NOTICE!

Use 3/4-inch (20-mm) NPS fittings for the holes on the bottom and back of the box. Use 1/2-

inch (15-mm) NPS fittings for the side holes.

WARNING!

A stud diameter of 6.4 mm (1/4 inch) to 8 mm (5/16 inch) able to withstand a 120 kg (265 lb)

pull-out force is recommended. The mounting material must be able to withstand this pull out

force. For example, 19-mm (3/4-inch) minimum for plywood.

Содержание VG5 600 Series

























































































Результаты поиска

Содержание VG5 600 Series

Отзывы:

Похожие инструкции для VG5 600 Series

Бренды по названию

Популярные бренды

Bosch VG5 600 Series, Руководство по установке

Результаты поиска

Содержание VG5 600 Series

Отзывы:

Похожие инструкции для VG5 600 Series

Бренды по названию

Популярные бренды