Bosch VG5 600 Series Скачать руководство пользователя

Страница: 28 / 88

en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts

AutoDome 600 Series Analog PTZ Camera

F.01U.265.793 | 2.0 | 2012.02

Installation Manual

Bosch Security Systems, Inc.

For a Mast or pole installation

The metal straps included with the Mast mount accommodate a pole with a diameter of

100–380 mm (4–15 in.). You must use a banding tool (sold separately) for a mast or pole

installation. In addition, you must obtain a 3/4 in. (20-mm) right angle conduit connector

through which you route the wires that connect to the pendent arm.

Follow the instructions provided with the banding tool to securely mount the Mast

Plate to the pole. Contact your Bosch Sales Representative to order Banding Tool

P/N TC9311PM3T.

Secure the Mounting Plate to the Mast Plate using the four (4) 3/8 x 1-3/4-inch bolts

and split lock washers (supplied).

Remove one of the rubber gaskets from the Mounting Plate.

Once the Mounting Plate (item 1, below) is attached to the Mast Plate (item 2),

connect the right angle conduit (item 3) to the Mounting Plate through the empty

conduit hole as shown below:

Ensure that the mounting plate is secure.

Содержание VG5 600 Series

























































































Результаты поиска

Содержание VG5 600 Series

Отзывы:

Похожие инструкции для VG5 600 Series

Бренды по названию

Популярные бренды

Bosch VG5 600 Series, Руководство по установке

Результаты поиска

Содержание VG5 600 Series

Отзывы:

Похожие инструкции для VG5 600 Series

Бренды по названию

Популярные бренды