Bosch DDU 7 Скачать руководство пользователя страница 69

Страница: 69 / 156

Display Unit DDU 7

CAN Bus | en

Bosch Motorsport

Manual

04.02.2019 | V 02 |

Drag + Drop

The measurement element displays the values of the assigned channel.

Connect PC to the vehicle and switch to ‘Race Mode’ by clicking ‘F11’ on the keyboard to
display online data.

9.2.8

Import a CAN database (DBC) file

Right-click on CAN Input of desired bus (CAN1 or CAN2).

Select ‘Import DBC file’ from menu.
A file browser opens.

Select DBC file to import and click ‘OK’ when done.
A channel import window opens.

Select desired channels on the left and use the ‘Add’ button to add them to import list.

Click ‘OK’ when complete.
The channels are inserted in the Data window.

9.2.9

Export RaceCon CAN configuration

Right-click on CAN Input of desired bus (CAN1 or CAN2).

Select ‘Export…’ from menu. An ‘Export Selection’ window opens.

Содержание DDU 7





























































































































































Результаты поиска

Содержание DDU 7

Отзывы:

Похожие инструкции для DDU 7

Бренды по названию

Популярные бренды

Bosch DDU 7, Руководство пользователя

Результаты поиска

Содержание DDU 7

Отзывы:

Похожие инструкции для DDU 7

Бренды по названию

Популярные бренды