Bosch DDU 7 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 156

background image

Display Unit DDU 7

Firmware | en

137

Bosch Motorsport

Manual

04.02.2019 | V 02 |

15

Firmware

15.1

Firmware and configuration

DDU 7 holds 4 types of data:
Firmware: the software (PST program file) of the DDU 7.
Configuration: the configuration of Input channels, CAN I/O, PWM, display configuration,
rec telemetry configuration.
Calibration data: Characteristic curves and offsets created by online calibration at the vehicle.
Recorded data: Measurement data recorded during vehicle operation.

15.2

Firmware update

The scheme shows the process during each connection between RaceCon and DDU 7.

Version match

Version does not match

Firmware version
consistency check

Firmware check
successful

Update firmware

Change program
archive in RaceCon

DDU 8

RaceCon

15.2.1

Performing the firmware update

Firmware update is only possible if the DDU 7 is connected to RaceCon.
The configuration of Input channels, CAN I/O, display, rec telemetry will not be
changed.

«
...
135
136
137
138
139
...
»

Содержание DDU 7





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DDU 7

Бренд: Rae Страницы: 71

Бренд: Garmin Страницы: 16

MultiSync LCD2180WG-LED

Бренд: NEC Страницы: 18

Бренд: JEA Technologies Страницы: 22

Data Industrial 3100 Series

Бренд: Badger Meter Страницы: 32

Бренд: Mottura Страницы: 40

Бренд: J-Tech Digital Страницы: 10

Бренд: Beurer Страницы: 104

Бренд: Kardioline Страницы: 53

Бренд: Dahua Страницы: 6

Бренд: Newhank Страницы: 11

Бренд: Daewoo Страницы: 2

Бренд: Slingbox Страницы: 12

Designjet 9000s Series

Бренд: HP Страницы: 392

Бренд: HP Страницы: 4

Бренд: LARTET Страницы: 33

LCD1770VX - MultiSync - 17" LCD Monitor

Бренд: NEC Страницы: 52

LCD1810X-BK - MultiSync 18" Ambix Digital

Бренд: NEC Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды