Bopp & Reuther UR06 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 55

background image

Operating Manual

Universal Flow Computer UR06

Bopp & Reuther

A-EN-08728-URRev.B

Subject to changes

Page 53 of 55

Messtechnik GmbH

E11

EEprom Para.

Parameter after device restart outside
the permissible range

Default value is used for the
affected parameter.

E12

EEprom count.

Incorrect check sum of the counters
saved in the EEPROM

E13

Pulses>max

Buffer overflow. Pulse value or
minimum pulse width has been set
incorrectly.

Output pulses are lost. No
influence on the displayed
counters.

E14

Mathematics

Incorrect configuration, incorrect
parameters

No re-evaluation

E15

Timeout LCD

Communication between the basic
device and the display interrupted

No influence on the re-
evaluation

E16

CRC EEPROM

Log (EEPROM) defective or not
installed

E17

Time setting

Clock defective

Incorrect time, tariff values
incorrect. No influence on the
re-evaluation

E33
E65
E97

Config. temp. 1
Config. temp. 2
Config. temp. 3

Error in the configuration of the
temperature input.

E34
E66
E98

Temperature 1
Temperature 2
Temperature 3

Temperature measurement faulty.
Incorrect configuration, short circuit,
cable break.

E35
E67
E99

Config. pressure 1
Config. pressure 2
Config. pressure 3

Error in the configuration of the
pressure input.

E36
E68
E100

Pressure 1
Pressure 2
Pressure 3

Measured variable outside the
measuring range. Wiring error.
Pressure transmitter is selected but not
connected or the current is less than
3.6mA.
No pressure transmitter connected or
no default value for gaseous media.

Measured value fails or
calculation is carried out with
default values

E37
E69

Conf. density 1
Conf. density 2

Error in the configuration of the density
measurement.

E38
E70

Density 1
Density 2

Density measurement faulty or outside
the specified area for the fluid.

Default value is used for
calculations.

E39
E71

Conf. dp 1
Conf. dp 2

Error in the configuration of the
differential pressure input.

dp=0

E40
E41
E42
E72
E73
E74

dp 1
dp 1A
dp 1B
dp 2
dp 2A
dp 2B

Measured variable differential pressure
outside the measuring range. Wiring
error. Differential pressure transmitter
is selected but not connected or the
current is less than 3.6mA.

dp=0

E43
E75

Conf. pri. transm.
Conf.sec. transm.

Error in the configuration of the primary
transmitter / secondary transmitter.

Flow rates are set to 0

E44
E76

Primary transmitter
Secondary
transmitter

Mass/Volume flow is set to 4-20mA for
the transmitter and the current falls
below 3.6 mA.

Flow rates are set to 0

E45
E77

Base density 1
Base density 2

E46
E78

Saturated steam 1
Saturated steam 2

Saturated steam monitor active and
measured values outside the saturated
steam line.

Saturated steam parameters
are used for the further
calculation.

E47
E79

GERG 1
GERG 2

Incorrect GERG parameters.

Calculation with constant
compressibility.

E49
E81

Comp pulse 1
Comp pulse 2

Number of permitted error pulses
exceeded. (only dual pulse)

E50
E82

Zero balance 1
Zero balance 2

Zero balance faulty (only EWZ211)

dp=0

E51

Volume 1

Measured variable fault fort he volume

No re-evaluation

«
...
51
52
53
54
55
»

Содержание UR06
























































Отзывы:

Нет отзывов

Похожие инструкции для UR06

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: M-system Страницы: 13

Бренд: TC Electronic Страницы: 20

Бренд: Ulvac Страницы: 18

Бренд: YOSensi Страницы: 26

Бренд: YOSensi Страницы: 26

Бренд: X-laser Страницы: 17

Бренд: Magnet-physik Страницы: 32

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренд: Alma Страницы: 69

Cerabar S PMC71

Бренд: Endress+Hauser Страницы: 48

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды