Blaze King 2205 Скачать руководство пользователя страница 19

DATE PRINTED: 2/8/05                            Revision Date: 04/15/04 

OM-2205                                                                                                         Page 19 

DO NOT:  

Use tools to operate controls, only use your hand to push in and turn the controls. 

DO NOT:

  Try to repair the appliance. Call a qualified service technician. 

DO NOT:  

Use this appliance if any part has been under water. Immediately call a qualified service technician to inspect 

the appliance and replace any part of the gas control system which has been under water. 

DO NOT: 

 Use this appliance if you  smell gas. 

WHAT TO DO IF YOU SMELL GAS: 

OPEN WINDOWS. 

DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE THE PHONE IN YOUR BUILDING. 

EXTINGUISH ANY OPEN FLAME. 

IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE AND FOLLOW THE GAS SUPPLIER’S IN-
STRUCTIONS. 

OPERATING INSTRUCTIONS—PRE-START UP CHECK LIST 

START-UP PROCEDURE 

1. Set  the  thermostat,  if  present,  to  the  lowest  level.  Switch 

burner switch to 

OFF. 

Set the flame adjustment knob to the 

HI

  position.  Press  slightly  and  turn  the  control  knob 

clockwise 

 to the 

OFF

 position and wait 5 minutes; thus 

allowing any gases to escape which may have accumulated 
in  the  combustion  chamber.  IF  YOU  SMELL  GAS 

STOP! 

 

FOLLOW INSTRUCTIONS ON PAGE 19. 

(

Note: 

LP  gases  do  not  vent  upward).  Then  follow  steps  2 

and 3 to establish pilot. 

2. Press slightly and turn control knob counterclockwise 

 to 

PILOT

  position;  depress  control  knob  and  light  pilot  by 

repeatedly  pressing  the  sparker.  Venting  of  air  may  take 
place at the pilot prior to the flow of fuel gases. Once flame 
is  established,  hold  knob  depressed  for  approximately    60 
sec. 

3. Release  knob.  If  the  pilot  will  not  light  or  the  control  knob 

does  not  pop  up  when  released,  turn  the  control  knob  to 

OFF

 and call your service technician or gas supplier. If the 

pilot should go out, turn the control knob to 

OFF 

position and 

repeat steps 1, 2 and 3. 

Note: 

this will allow reset of INTERLOCK for proper lighting 

of pilot. 
Also the Honeywell valve is equipped with a safety  lockout, 
once in the off position you must wait until the thermopile has 
cooled  down  before  attempting  to  light  the  pilot 
(approximately 3 minutes). 

4. Press  and  turn  control  knob  counterclockwise 

  to 

ON 

position. 

5. Turn flame and heat adjustment knob to the desired comfort 

level from 

HI

GH to 

LO

W. 

6. Turn thermostat to the desired comfort level or turn ON/OFF 

switch to the ON position. 

NOTE:  When first fired, the unit will produce an odor. This is 
normal  and  is  part  of  the  paint  curing  process.  It  is 
recommended that you open a few windows to ventilate the 
room. This will be noticeable for at least 6 hours. During the 
first hour smoke detectors in the house may be set off. 

Following  the  initial  burn-in  period,  the  glass  panel  may 
require cleaning.  

CAUTION: Do not clean the glass when the appliance is 
hot!

 

When the appliance is fired from cold the glass may fog up. 
This is due to condensations and is normal. 

Make yourself familiar with these instruction before operating 
the appliance. 

Check any loose electrical wires that may cause a shock. 

Check around the appliance for gas leaks. IF YOU SMELL 
GAS,  follow  the  instructions  on  the  front  cover  of  this 
manual. 

Check  to  see  that  logs  are  correctly  positioned.  The  pilot 
light should be visible. 

Check to make sure that venting is secure. 

Check  all  external  parts,  such  as  grills,  doors  and  control 
cover are properly attached and fastened. 

CAUTION: Do not turn the unit off and on again within a 
minimum of  a 60 second wait.

 

FOR YOUR SAFETY READ - BEFORE LIGHTING 

WARNING:  

WARNING:  

WARNING:  

WARNING:  

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY 

                                 RESULT CAUSING PROPERTY AND/OR PERSONAL INJURY 

FINAL CHECK 

INSTALLER: Before leaving the appliance with the customer, 
you must check the operation of the appliance: 

Thoroughly check the entire appliance for gas leaks. 

Check  correct  rating  by  clocking  the  appliance  at  15 
minutes (see label). 

Check flame picture. Adjust primary air if required (see 
page 14). 

Take time to go through the unit with the customer. 

Содержание 2205
































Отзывы: