Blaze King 2205 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 31

Blaze King 2205 Скачать руководство пользователя страница 10

DATE PRINTED: 2/8/05 Revision Date: 04/15/04

OM-2205 Page 10

INSTALLATION

VENTING
Please follow the venting instructions as strictly as possible to obtain the best performance from the appliance.

THESE ARE THE ONLY VENTING COMPONENTS APPROVED FOR USE WITH THE MODEL 2205.

Some general venting rules for best venting
performance:

1. Observe local code restrictions, if any, regarding

the installation of this type of gas appliance.

2. Observe the venting chart on the following page.

3.

Terminate the vent with a suitable vent

termination.

Duravent

Assembly

(Shown with high wind cap)

Security Chimney

Assembly

(wind cap)

The exhaust and air intake pipe must be securely fastened to the appliance and terminal and all joints must be secured

using a minimum of 3 screws evenly spaced around the pipe.

Approximately 1” from the end of the 3” appliance exhaust pipe outlet at the appliance air intake pipe and at the 3” terminal

connections apply a bead of Mil Pac or other high heat silicone 1/4” wide. Slide the 3” pipe onto the appliance and secure

with 3 screws evenly spaced to the outlet.

Only use approved 3” double walled flex liner for correct installation

VENT ASSEMBLY

Air inlet

3” Double
wall Flex

Self Tapping
Screw

Mil Pack Seal-
ant

Exhaust

Duravent Product Numbers:

High Wind Cap                                       #991
Adapter                                                   #923GK

Optional Flex Connectors                    #2150

(2 required if used)

Security Chimney

Assembly #3PDVCV

This direct vent appliance must be installed
using an approved venting system. All
vent pipe joints must be sealed with a high
temperature sealant in order to meet the
ANSI/CSA leakage limit standards.

When installed in accordance with the

manufacturer’s instructions the combustion

air supply will be in the same pressure zone

as the vent outlet.

«
...
8
9
10
11
12
...
»

Содержание 2205
































Отзывы:

Нет отзывов