Black Box Compact T1 MT850A Скачать руководство пользователя

Страница: 489 / 592

Compact T1 - Release 6.1

14-15

Router (CMG) Card

Card Configuration

set (router-wan) dlci
Configure the DLCI for a specified WAN interface that will be using a frame
relay encapsulated trunk

set (router-wan) gre
Configure the GRE tunneling for a specified WAN interface

set (router-wan) ip
Set the IP traffic handling on the WAN interface

set (router-wan) ip address
Set the IP address for a WAN interface

set (router-wan) ipx
Set the IPX traffic handling on the specified WAN interface

set (router-wan) nat
Configure Network Address Translation (NAT) on a specified WAN
interface

set (router-wan) other
Set the traffic handling of protocols other than IP or IPX on the specified
WAN interface

set (router-wan) ppp
Configure the PPP (Point-to-Point Protocol) on the specified router card

set (router-wan) rip
Set the type or RIP updates on the WAN interface

set (router-wan) stp
Configure the Spanning Tree Protocol on the specified WAN

set (router-wan) trunk
Configure the trunk port for a specified WAN interface

set (router-wan) up/down
Set the specified WAN interface up or down

show (router)
Displays the current Router settings

show (router) dhcp
Displays the current DHCP settings for the Router

show (router) dns
Displays the current DNS setup for the router card

Содержание Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Compact T1 MT850A

Отзывы:

Похожие инструкции для Compact T1 MT850A

Бренды по названию

Популярные бренды

Black Box Compact T1 MT850A, Руководство пользователя

Результаты поиска

Содержание Compact T1 MT850A

Отзывы:

Похожие инструкции для Compact T1 MT850A

Бренды по названию

Популярные бренды