Black Box Compact T1 MT850A Скачать руководство пользователя | Manualshive

Страница: 250 / 592

background image

5-166

Compact T1 - Release 6.1

CLI Commands

set

set (router-trunk) encapsulation

Use the set (router-trunk) encapsulation command to specify the encapsulation to use on the
Router interface.

Syntax:

set {rtr-trunk-addr} encapsulation {setting}

Example:

set 2:1:5 encapsulation pppofr

The example will configure encapsulation on the Router card in slot 2, port 1,
trunk 5 to PPP over Frame Relay.

{rtr-trunk-addr}

{setting}

set (router-trunk) multilink group

Use the set (router-trunk) multilink group command to specify a router trunk to be part of a
multilink PPP group. Note: It is recommended, for performance, that all of the individual links
in the multilink group have approximately the same bandwidth.

Syntax:

set {rtr-trunk-addr} multilink group {number}

Example:

set 3:1:1-2 multilink group 1

The example will form a multilink PPP group that combines trunk 1 and 2.

set 3:1:3 multilink group

The example will add a third trunk to the multilink PPP group from above.

{rtr-trunk-addr}

{number}

The multilink group number.

slot

Slot number (1-6) that contains the Router (IP or CMG) card

port

Port number of the Router is 1

trunk

Trunk number for this port, 1-24

fr

Frame Relay as per RFC 2427

ppp

Point-to-Point Protocol (PPP) as per RFC 1661 and 1662

pppofr

PPP over Frame Relay as per RFC 1973

slot

Slot number (1-6) of the Adit that contains the Router (IP or CMG) card

port

Port number of the Router is 1

trunk

Trunk number for this port, 1-24

«
...
248
249
250
251
252
...
»

Содержание Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact T1 MT850A

Бренд: NEO Страницы: 25

Бренд: Baracoda Страницы: 35

Бренд: Unitech Страницы: 33

Бренд: Quest Payment Systems Страницы: 37

Бренд: Vectron Страницы: 112

rexroth IndraControl VAC 08.1

Бренд: Bosch Страницы: 40

Rexroth ctrlX I/O XI312204

Бренд: Bosch Страницы: 8

Бренд: Mitsubishi Electric Страницы: 26

Бренд: Mitsubishi Electric Страницы: 6

Бренд: Mitsubishi Electric Страницы: 6

Lossnay PZ-4GS-E

Бренд: Mitsubishi Electric Страницы: 4

Бренд: Mitsubishi Electric Страницы: 13

Бренд: Samson Страницы: 70

PINPAD 8006L1-1CRA Series

Бренд: XAC Страницы: 4

Бренд: E-Service Страницы: 17

Бренд: Kronos Страницы: 146

Бренд: A.I. HARDWARE Страницы: 18

Бренд: POSIFLEX Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды