Black Box Compact T1 MT850A Скачать руководство пользователя

Страница: 388 / 592

7-4

Compact T1 - Release 6.1

FXO Voice Card

Technical Specifications

FXO Transmission Performance

Return Loss: ERL > 26 dB, SRL > 18 dB with respect to 900

Ω + 2.16µ

Transhybrid Loss: ERL > 26 dB, SRL > 18 dB with respect to 900

Ω + 2.16µ

Idle Noise: A/D < 16 dBrnC0, D/A, 12 dBrnC0

Crosstalk Coupling: < 70 dB at 0 dBrn0

Signal/Distortion: > 35 dB with 1004 Hz, 0 dBm0 input

Overload: +3.0 dBm/900

Ω

Frequency Response: +0.3 dB -1.0 dB from 300 to 3400 Hz

Encoding:

-law 255 for U.S. and Canada as defined in CCITT G.711 and G.712

Terminating Impedance: 900

Ω

2.16µ

Transmit Gain/Loss: +7 to -9 dB, switch selectable per card

Receive Gain/Loss: +7 to -9 dB, switch selectable per card

Modem Support: Full compatibility with V.90 modems

FXO Signaling Performance

DC Loop Range: > 1600

Ω

loop or ground start

Ringer Equivalency Number (REN): 0.4B (AC)

Ringing Voltage Detection: detects Class A ringing follows distinctive ringing

FXO DC Resistance: 100

Ω

Maximum DC: 150 mA

Overvoltage: UL 1950, FCC Part 68 lightning protection

Overcurrent: 600 V rms, 60 Amps

Protection: solid-state (fuseless) overvoltage and over current protection

Termination Type: FXO loop start or ground start, switch selectable per card or
via management interface per channel

Signaling Selection: DPT functionality enabled/disabled on all 8 channels

Address Signaling: DTMF or dial pulse

Calling Party Disconnect: detects and forwards current interruption to disconnect
answering devices and modems

Содержание Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Compact T1 MT850A

Отзывы:

Похожие инструкции для Compact T1 MT850A

Бренды по названию

Популярные бренды

Black Box Compact T1 MT850A, Руководство пользователя

Результаты поиска

Содержание Compact T1 MT850A

Отзывы:

Похожие инструкции для Compact T1 MT850A

Бренды по названию

Популярные бренды