Black Box Compact T1 MT850A Скачать руководство пользователя | Manualshive

Страница: 267 / 592

background image

Compact T1 - Release 6.1

5-183

CLI Commands

set

set (router-wan) gre

Use the set (router-wan) gre command to configure Generic Routing Encapsulation tunneling
for a specified WAN interface.

set (router-wan) gre address

Use the set (router-wan) gre address command to configure the IP addresses for GRE
tunneling for a specified WAN interface.

Syntax:

set {rtr_card-addr} {"wan-name"} gre address

{local_ip-addr} [remote-ip-addr] ["tunnel-name"]

Example:

set 3 "LosAngeles" gre address 10.0.0.0 20.0.0.0

"LATunnel"

The example will set the WAN interface named "LosAngeles" to the IP
addresses to be 10.0.0.0 and 20.0.0.0.

Note: A set 3 "LosAngeles" gre ip all command is required before this
command.

{rtr_card-addr}

The slot number (1-6) that contains the Router (IP or CMG) card.

{"wan-name"}

The WAN interface to modify. The name must be enclosed in quotes.

{local-ip-addr}

The IP Address of the local end of the tunnel, in the form of xxx.xxx.xxx.xxx, where xxx
is between 0-255.

[remote-ip-addr]

The IP Address of the far end of the tunnel, required if GRE tunneling is set to All,
prohibited if GRE tunneling is set to By Network. In the form of xxx.xxx.xxx.xxx, where
xxx is between 0-255.

["tunnel-name"]

A symbolic name to give to this tunnel, required if GRE tunneling is set to All, prohibited
if GRE tunneling is set to By Network. Up to 12 characters, enclosed in quotes.

«
...
265
266
267
268
269
...
»

Содержание Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact T1 MT850A

Бренд: NEO Страницы: 25

Бренд: C-Data Страницы: 24

Бренд: Partner Страницы: 54

Бренд: Festo Страницы: 160

Бренд: CCV Страницы: 30

Бренд: DAP Technologies Страницы: 2

Cinterion BGS5T USB

Бренд: Gemalto Страницы: 50

Бренд: Xitex Страницы: 32

Бренд: Holtkamp Страницы: 28

AXIUM DX8000-BASE-W2

Бренд: Ingenico group Страницы: 19

Бренд: MVG industries Страницы: 22

Бренд: MVG Страницы: 36

Бренд: Idemia Страницы: 11

Trakker Antares 2455

Бренд: Intermec Страницы: 12

Бренд: EBN Technology Страницы: 15

Бренд: Partner Страницы: 31

Бренд: Unitech Страницы: 60

Бренд: Beckhoff Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды