manualshive.com logo in svg

Black Box Compact T1 MT850A, Руководство пользователя

Компактный T1 MT850A это мощный черный ящик, который гарантирует безупречную безопасность и надежность. Скачайте бесплатное руководство пользователя с нашего сайта, чтобы в полной мере пользоваться всеми функциями этого устройства. Посетите manualshive.com для загрузки.

Поделиться
Скачать
background image

5-80

Compact T1 - Release 6.1

CLI Commands

set

set (fxs5G)

Use the set (fxs5G) command to setup voice channels of an FXS 5G card. The command 
specifies the list of voice channels, and the setting to apply. 

Syntax:

set {fxs5G-addr} {setting} 

Example:

set 3:1-8 impedance 19

Sets the impedance of the FXS 5G card, in slot 3, to 900 ohms +2.16

µ

F

 (

µ

-Law), see show impedance for the listing of index numbers.

{fxs5G-addr}

Voice channels to apply setting to, in the form of {slot:port}.

{setting}   

slot

Slot number 1 - 6, location of the FXS 5G card

port

Port number or range

impedance

Sets the line impedance (see the following chart). Default for the FXS 
5G is index 19 (900 ohms +2.16

µ

F 

µ

-Law)

See show impedance command.

rxgain

The Receive direction is Network to Analog, with a range of -12 to +6 
(dB). Available in .25 dB increments.Default setting is -6

signal

Set the DS0 signaling type

gs

Set to Ground Start signaling

gsrb

Set to Ground Start signaling with reverse battery

gsw

Set to Ground Start Wink signaling

gswrb

Set to Ground Start Wink signaling with reverse battery

ls

Set to Loop Start signaling

lsrb

Set to Loop Start signaling with reverse battery

txgain

The Transmit direction is Analog to Network, with a range of -12 to +6 
(dB). Available in .25 dB increments. Default setting is -3

winktime

Set the wink time from 105 ms to 300 ms in 3 ms increments. Enter 
value or type "Default" (135 ms). Setting the wink time for any channel 
sets it for all channels on this card.

Содержание Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact T1 MT850A

Fametech POS-6000 Series Service Manual preview
POS-6000 Series
Бренд: Fametech Страницы: 35
Bosslan BOSSTX2B User Manual preview
BOSSTX2B
Бренд: Bosslan Страницы: 87
Lenze E94AZKHTKAE003 Mounting Instructions preview
E94AZKHTKAE003
Бренд: Lenze Страницы: 10
Holtkamp UNO 7600/XL Operating Instruction preview
UNO 7600/XL
Бренд: Holtkamp Страницы: 36
E-Service Nayax Installation Manual preview
Nayax
Бренд: E-Service Страницы: 17
POSIFLEX KS - 6215N User Manual preview
KS - 6215N
Бренд: POSIFLEX Страницы: 20
POSIFLEX KS-6810 SERIES Technical Manual preview
KS-6810 SERIES
Бренд: POSIFLEX Страницы: 50
Radiant P1550 Configuration Manual preview
P1550
Бренд: Radiant Страницы: 12
NCR RealPOS 5953 User Manual preview
RealPOS 5953
Бренд: NCR Страницы: 100
Festo VABA-S6-1-AP Operating Instructions Manual preview
VABA-S6-1-AP
Бренд: Festo Страницы: 14
EC Line EC-WT-10 User Manual preview
EC-WT-10
Бренд: EC Line Страницы: 31
Partner SP-5514 Quick Start Manual preview
SP-5514
Бренд: Partner Страницы: 2
Aratek VC331 User Manual preview
VC331
Бренд: Aratek Страницы: 24
Card System Technologies 510AR General Reference Manual preview
510AR
Бренд: Card System Technologies Страницы: 25
Tysso TP-1615 User Manual preview
TP-1615
Бренд: Tysso Страницы: 20
Seypos POS335 Hardware System preview
POS335
Бренд: Seypos Страницы: 44
PC-EFTPOS ANZ Quick Reference Manual preview
ANZ
Бренд: PC-EFTPOS Страницы: 28
Hytera PT560H F5 TETRA Manual preview
PT560H F5 TETRA
Бренд: Hytera Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды