manualshive.com logo in svg

Black Box Compact T1 MT850A, Руководство пользователя

Компактный T1 MT850A это мощный черный ящик, который гарантирует безупречную безопасность и надежность. Скачайте бесплатное руководство пользователя с нашего сайта, чтобы в полной мере пользоваться всеми функциями этого устройства. Посетите manualshive.com для загрузки.

Поделиться
Скачать
background image

13-12

Compact T1 - Release 6.1

Router (IP) Card

Card Configuration

l 

set (router-lan) filter forward
Set the forwarding mode for Layer 2 filters added to the specified LAN 
interface.

l 

set (router-lan) framing
Set which ethernet frame types are supported on the Router LAN interface.

l 

set (router-lan) gateway
Specify a default IP gateway for the specified LAN interface.

l 

set (router-lan) ip address
Specify an IP address for the specified LAN interface.

l 

set (router-lan) ipx network
Specify an IPX network numbers for the four IPX LAN frame types.

l 

set (router-lan) phy
Specify the ethernet PHY (physical specifications) speed and mode. 

l 

set (router-lan) rip
Set the IP RIP for the LAN interface.

l 

set (router-lan) stp
Setup the Spanning Tree Protocol on this interface.

l 

set (router-lan) up/down
Set the LAN interface up or down.

l 

set (router-trunk) encapsulation
Specify the encapsulation to use on the Router interface.

l 

set (router-trunk) multilink group
Specify that a trunk is part of a multilink PPP group

l 

set (router-trunk) up/down
Set the Router trunk up or down.

l 

set (router-wan) dlci
Configure the DLCI for a specified WAN interface that will be using a frame 
relay encapsulated trunk.

l 

set (router-wan) gre
Configure the GRE tunneling for a specified WAN interface.

l 

set (router-wan) ip
Set the IP traffic handling on the WAN interface.

Содержание Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact T1 MT850A

National Instruments SCXI-1300 Installation Manual preview
SCXI-1300
Бренд: National Instruments Страницы: 10
Unitech Tashi MT680-AMWTAG User Manual preview
Tashi MT680-AMWTAG
Бренд: Unitech Страницы: 35
Keithley STP-36 Packing List preview
STP-36
Бренд: Keithley Страницы: 4
Bittium Mx Rugged B User Manual preview
Mx Rugged B
Бренд: Bittium Страницы: 43
Invixium IXM TITAN Installation Manual preview
IXM TITAN
Бренд: Invixium Страницы: 34
InVid PAR-P2TEMPTABLET User Manual preview
PAR-P2TEMPTABLET
Бренд: InVid Страницы: 64
ELTEX NTU-52V User Manual preview
NTU-52V
Бренд: ELTEX Страницы: 48
Denso BHT-M80 Series Operator'S Manual preview
BHT-M80 Series
Бренд: Denso Страницы: 2
Denso BHT-M60 Series Safety Precautions preview
BHT-M60 Series
Бренд: Denso Страницы: 24
Welcat GTX-100 User Manual preview
GTX-100
Бренд: Welcat Страницы: 171
btsr SMART MATRIX FEEDER Operating Manual preview
SMART MATRIX FEEDER
Бренд: btsr Страницы: 87
Nautilus Hyosung MX2600SE Quick Reference Manual preview
MX2600SE
Бренд: Nautilus Hyosung Страницы: 2
Quark-Elec QK-AT011 Manual preview
QK-AT011
Бренд: Quark-Elec Страницы: 8
Qume QVT 101 Maintenance Manual preview
QVT 101
Бренд: Qume Страницы: 74
FEC AerPOS AP-3617 System Manual preview
AerPOS AP-3617
Бренд: FEC Страницы: 49
TEC ST-6500 Setup Manual preview
ST-6500
Бренд: TEC Страницы: 25
GECMA CHALLENGER 15 Inch Operating And Installation Instructions preview
CHALLENGER 15 Inch
Бренд: GECMA Страницы: 50
NCR 5977-1000 User Manual preview
5977-1000
Бренд: NCR Страницы: 172

Бренды по названию

Популярные бренды

Загрузить еще бренды