Black Box Compact T1 MT850A Скачать руководство пользователя | Manualshive

Страница: 251 / 592

background image

Compact T1 - Release 6.1

5-167

CLI Commands

set

set (router-trunk) up/down

Use the set (router-trunk) up/down command to set the WAN trunk up or down. When the
Router trunk is set down a link failure will not cause an alarm. This can be used to eliminate
alarms from Router trunks that are not in-use. When the Router trunk is set up, a link failure on
the WAN trunk will cause an alarm to be reported to the Adit.

Syntax:

set {rtr-trunk-addr} {down|up}

Example:

set 2:1:1 down

The example will set the first Router trunk interface on slot 2 down.

{rtr-trunk-addr}

In the form {slot:port:trunk}.

{up|down}

slot

Slot number (1-6) of the Adit that contains the Router (IP or CMG) card.

port

Port number of the Router is 1.

trunk

Trunk number for this port, 1-24.

down

Set the WAN down.

up

Set the WAN up.

«
...
249
250
251
252
253
...
»

Содержание Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact T1 MT850A

Бренд: Moneris Страницы: 86

Бренд: wtw Страницы: 32

Бренд: Spire Страницы: 2

Бренд: gefran Страницы: 52

Бренд: TSYS Страницы: 2

Бренд: Chainway Страницы: 39

Бренд: Vertex Wireless Страницы: 35

RemoteSAT RST100B

Бренд: Beam Страницы: 40

Бренд: OKPOS Страницы: 20

Бренд: Invenco Страницы: 67

Бренд: Wincor Nixdorf Страницы: 43

Бренд: Omron Страницы: 2

Бренд: Unique Secure Страницы: 9

Бренд: Crestron Страницы: 4

Бренд: Orderman Страницы: 21

Бренд: wallee Страницы: 6

Бренд: UIC Страницы: 4

Бренд: ZETRON Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды