Black Box Compact T1 MT850A Скачать руководство пользователя | Manualshive

Страница: 210 / 592

background image

5-126

Compact T1 - Release 6.1

CLI Commands

set

set (router) mgcp up

Use the set (router) mgcp up command to start MGCP processing of incoming messages
and endpoint events. MGCP must be up for the Customer Media Gateway to properly
interact with an external call agent. The CMG notifies the call agent by means of one or
more Restart in Progress (RSIP) commands with the Restart Method parameter set to
"restart". An RSIP is sent for each voice channel which is configured as "up", after an initial
random delay of not more than 30 seconds. If MGCP is configured as up when a CMG
board reset or power cycle occurs, RSIP commands will be sent to the call agent when the
board is ready for MGCP operation. This command applies to the CMG Router card only.

Syntax:

set {cmg_card-addr} mgcp up

Example:

set 1 mgcp up

The example will start MGCP processing, with call agent with call agent
notification, for the CMG card in slot 1.

{cmg_card-addr}

The slot number (1-6) that contains the CMG card.

set (router) mgcp version

The set (router) mgcp version is an interoperability command to specify the version of the
MGCP protocol which is running on the Customer Media Gateway. This version must be
compatible with the version of MGCP running on the call agent. This command applies to
the CMG Router card only.

Syntax:

set {cmg_card-addr} mgcp version {ietf01|ietf10|ncs}

Example:

set 1 mgcp version ietf01

The example will set the MCGP protocol version to IETF version 0.1, for the
CMG card in slot 1.

{cmg_card-addr}

The slot number (1-6) that contains the CMG card.

{ietf01|ietf10|ncs}

ietf01

IETF MGCP version 0.1, as specified in an IETF MGCP Internet draft

ietf10

IETF MGCP version 1.0, as specified in IETF RFC 2705 (Default)

ncs

PacketCable MGCP version NCS 1.0

«
...
208
209
210
211
212
...
»

Содержание Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact T1 MT850A

Vx680 BT Series

Бренд: VeriFone Страницы: 2

Бренд: ZIEHL-ABEGG Страницы: 21

Бренд: Equinox Systems Страницы: 2

SCPSt 07 G02 NC

Бренд: Schmalz Страницы: 74

Бренд: HANTEL Страницы: 105

Бренд: Philips Страницы: 40

Бренд: Philips Страницы: 44

Бренд: VeriFone Страницы: 5

AKI-CDC-MOD-12T

Бренд: Kollmorgen Страницы: 36

GTA-A8 TC-Touch

Бренд: Monitor POS Страницы: 22

GT-540P-3GWA-OEM2

Бренд: ICP DAS USA Страницы: 55

Бренд: Omron Страницы: 186

Бренд: Custom Audio Electronics Страницы: 16

Бренд: Custom Audio Electronics Страницы: 16

Бренд: Nailor Страницы: 146

Бренд: Zebra-Tech Страницы: 24

Morpho RapID Series

Бренд: Sagem Securite Страницы: 13

Бренд: MVG industries Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды