BinTec VICAS Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 202

background image

62

Configuring Protocols

V!CAS

ip.accesslists

This menu displays the IP Access Lists. The V!CAS has an Allow list and
a Deny list based on the mode of the entries configured here. Each entry
specifies an interface to monitor incoming traffic on and defines a set of
IP packets.

IP packets are tested to see if they match deny/allow entries. The de-

cision whether to route the packet is based on the following algorithm

Using Source and Destination Port Numbers

Along with the source and destination addresses, the Internet Protocol
uses source and destination ports numbers, to identify data connections
uniquely. The client side generates a number (xyz) which is used as the

V!CAS Setup Tool

BinTec Communications GmbH

[

IP

][

ACCESS

]

: IP Access Lists

vicas

M (Mode) values are: a (Allow), d (Deny)

Access Lists configured:

M Prt

Int./Partner

Src Address

Src Port

Dst Address

Dst Port

a

tcp

dialup1

any

any

any

any

d

tcp

dialup1

any

any

any

21

d

tcp

dialup1

210.1.2.3/24

any

any

23

d

tcp

dialup1

any

25-103

any

clients

ADD

DELETE

EXIT

IP

A

CCESS

L

ISTS

Allow List

empty?

Deny List

empty?

Match an

Allow entry?

Match a

Deny entry?

Route packet!

Discard packet!

yes

yes

yes

no

no

no

yes

no

Incoming

packet

«
...
68
69
70
71
72
...
»

Содержание VICAS











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VICAS

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 7

Бренд: D-Link Страницы: 41

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Quick Eagle Networks Страницы: 4

Бренд: Ubiquiti Страницы: 20

Бренд: AMG Systems Страницы: 2

Бренд: Ozenda Страницы: 116

Бренд: Acorn Computers Limited Страницы: 2

Бренд: Ubiquiti Страницы: 20

Бренд: Milesight Страницы: 15

TE100S8P - Fast Ethernet Switch

Бренд: TRENDnet Страницы: 11

Бренд: Matrix Switch Corporation Страницы: 54

Бренд: MCT Страницы: 12

Бренд: Black Box Страницы: 12

Бренд: Avigilon Страницы: 12

Бренд: WatchNet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды