BinTec VICAS Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 202

background image

Firmware

169

User’s Guide: Version 1.2

Firmware

Upgrading System Software

You may decide to upgrade your V!CAS’ internal system software in the
future to take advantage of new and enhanced features developed at
BinTec. System software upgrades are available via BinTec’s FTP server
via the WWW at http://www.bintec.de. There you’ll also find current in-
formation about new releases.

After obtaining the newest software you can perform the upgrade in

any of the methods described as follows:

• BOOTmonitor

(press the spacebar during bootup)

• update command

(while the system is running)

• TFTP

(retrieve the BOOT image via TFTP)

BOOTmonitor

After the internal self test has been successfully completed, the V!CAS
switches into BOOTmonitor mode and displays a BOOTmonitor prompt
to the screen, if a terminal is connected. Using the BOOTmonitor, you can
easily perform firmware upgrades, test a new software release, or remove
configuration files on your system.

To activate the BOOTmonitor the spacebar must be pressed within the

first 4 seconds, otherwise the system continues with its normal boot pro-
cedure and switches into normal operation mode. Pressing the spacebar
activates the BOOTmonitor as shown in Figure 4 below. As long as the
BOOTmonitor is active (or awaiting keyboard input), all LEDs will re-
main on.

The commands from the BOOTmonitor menu are self guiding, in-

forming/prompting you for confirmation along the way.

«
...
175
176
177
178
179
...
»

Содержание VICAS











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VICAS

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 7

Бренд: D-Link Страницы: 41

Бренд: Patton electronics Страницы: 8

Бренд: Intellinet Страницы: 2

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: Comway Страницы: 20

Бренд: Digisol Страницы: 22

Elinx EIR510 Series

Бренд: B&B Electronics Страницы: 2

Бренд: Casablanca Страницы: 13

Бренд: Active Communications Страницы: 10

Бренд: Chase Research Страницы: 114

ReadyNAS 3220 Series

Бренд: NETGEAR Страницы: 4

Бренд: JAKA Страницы: 37

Бренд: Socket Страницы: 28

Бренд: PRIZM Страницы: 8

Бренд: ActiveEye Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды