manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 92

 

 Maintenance

 

 

5-48 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Inspection and Maintenance of Power Unit

 (

Continued

) 

 

Seal Plate 

 

Inspect the seal plate I.D. and O.D. for nicks, dents or wear.  Replace the seal plate if damaged.  
(See Seal Plate Maintenance). 

 

Inspect the seal I.D. for nicks, cuts or cracks.  Replace the seal if damaged.  (See Seal Plate 
Maintenance). 

 

 
 
 
 
 

 

 

 

Gear Head 

 

Inspect the gear head, by rotating the shaft. 

 

If the shaft does not rotate, replace the gear head. 

 

If you feel a rough or gritty resistance while rotating the shaft, replace the gear head. 

 

Re-grease gear head with Max-Z-Lube grease every 80 hours of use. 

 

Squeeze grease in through the rotor shaft hole in the bottom of the gear head. 

 

Continue to supply grease until clean grease comes out of the grease holes in the ring 
gear.   

 

This method will thoroughly re-grease gear head and clean out debris trapped in the gear 
head. 

 

NOTE:

  

Use only Max-Z-Lube high performance lubricant.

 

 

 

Seal Plate 

Seal 

Shaft

 

Grease Holes 
(on both sides) 

Содержание Whizard AirMax MACH 3
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды