BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 32

Страница: 32 / 183

Instructions for Operation

4-8

Instructions for Operation
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Left Cover
Retaining
Screw

Pivot Support
Point

Housing
Slot

Screwdriver

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

NOTE:

Leave a slight tension on the

left cover retaining screw so the
blade housing will stay open on its own.

Step 8: Install Blade



Holding the tool blade side up, pry
open the blade housing with a
screwdriver.



Insert a new blade into the
housing.



Loosen the left cover retaining
screw to allow the housing to
close.



Tighten the right cover retaining
screw.



With left cover retaining screw ½
turn loose, adjust housing for proper fit.



Gently pry the housing open until the blade
rotates freely and has enough clearance
to allow the blade to move forward and
backward in the housing. Only a slight
amount of movement is necessary.



Tighten the cover retaining screws to the



recommended torque.

NOTE:

Recommended torque of 30-40 lb-in

(3.4-4.5 N-m).

IMPORTANT:

Be sure that the blade is free to move

in the housing. If the blade does not move freely, it
may cause the trimmer to overheat.

Left Cover
Retaining
Screw

Screwdriver

Содержание Whizard AirMax MACH 3
























































































































































































Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды