manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 47

 

Maintenance 

 

 

Manual No.  188000  
September 1, 2009 

 Maintenance  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

5-3 

 

Maintenance Schedule 

 

Description 

Maintenance Schedule 

Handpiece 

Daily 

Power Unit 

After Every 80 Hours of Use  

Hose Assembly 

As Required 

 

General Maintenance 

 

 

Drain filter bowls daily. 

 

Inspect filter for damage and dirt build-up.  Replace when necessary. 

 

Fill lubricator (oiler) daily or more often if needed. 

 

Verify oiler is set to deliver 3 drops of oil per minute. 

 

Verify air pressure is set at 90-100 psi.  

Do not exceed 100 psi!

 

 

Handpiece Maintenance 

 

 

 

W A R N I N G  

 

 

 

SHARP BLADES MAY CAUSE INJURY! 

 

FOR PROPER PROTECTION OF HANDS, A PROTECTIVE 

GLOVE SHOULD BE USED WHEN OPERATING THIS 

EQUIPMENT AND DURING THE HANDLING OF BLADES. 

 

ALWAYS

 

DISCONNECT

 

AIR

 

SUPPLY

 

AND

 

REMOVE

 

TOOL

 

FROM

 

HOSE

 

ASSEMBLY

 

PRIOR

 

TO

 

SERVICING. 

 

The Whizard

® 

AirMax MACH 3 Trimmer was designed to allow quick and easy removal of the 

handpiece from the hose assembly.  This allows the trimmer to be removed from the hose 
assembly while still on the production line.  The hose assembly can be left hanging on the 
production line and the handpiece can be returned to the knife room for service.  It is 
recommended that this procedure be followed.  The removal of the 10 feet (3.05 m) of hose will 
allow easier service, storage, and handling by knife room personnel. 

 

Required Tools for Handpiece Maintenance 

 

1 – Flat head screwdriver 
1 – Hex Wrench (supplied with the Whizard

®

 

AirMax MACH 3 Trimmer) 

Содержание Whizard AirMax MACH 3
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды