BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 120

Страница: 120 / 183

Cleaning

6-2

Cleaning
Whizard

AirMax MACH 3 Operating Instructions and

Parts List

Manual No. 188000
September 1, 2009

Periodic Cleaning During Use

Light rinsing during operation is recommended.

Thorough rinsing at each break is highly recommended to improve tool performance.

Cleaning after Daily Use

If handpiece is removed from hose assembly, install cap to prevent water and debris from
entering the motor during cleaning.

Fully disassemble the Whizard

AirMax MACH 3 trimmer head assembly and clean each part

thoroughly with a brush and cleaner. For best results, clean the Whizard

AirMax MACH 3

trimmer with Bettcher

XTRA

Heavy Duty Cleaner, diluted according to the directions on the

container.

After cleaning, rinse each part thoroughly with water and dry. Assemble the head

assembly per instructions in Section 5.

Cleaning Solutions

Avoid the use of aggressive cleaning products and all cleaning products containing NaOH
(sodium hydroxide) as they will damage the handpiece.

Содержание Whizard AirMax MACH 3
























































































































































































Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды