BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 83

Страница: 83 / 183

Maintenance

Manual No. 188000
September 1, 2009

Maintenance
Whizard

AirMax MACH 3 Operating Instructions and Parts

List

5-39

Assembly of TRIMVAC

AMX Handpiece

(Continued)

Step 7: Install Blade (Continued):

TRIMVAC

18AMX:



Carefully insert the blade.



Loosen the left cover retaining screw so the housing will close.

NOTE:

Be certain that the blade is free to move in the housing. If the blade does not move freely, it

may cause the trimmer to overheat.



Adjust the housing for proper running clearance.



When the housing is properly adjusted there will
be a slight “left to right” movement, plus a light
“up and down” movement.



If the blade does not move “left to right” and “up
and down”, pry the housing open slightly.



Retighten the cover retaining screws.

NOTE:

Recommended torque of 30-40 lb-in (3.4-4.5 N-m)

Содержание Whizard AirMax MACH 3
























































































































































































Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды