manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 37

 Instructions for Operation 

 

 

Manual No.  188000  
September 1, 2009 

 Instructions for Operation  
Whizard

® 

AirMax MACH 3 Operating Instructions and Parts 

List 

4-13 

 

Depth Gauge Adjustment 

 

 

 

 

W A R N I N G  

 

 

 

SHARP BLADES MAY CAUSE CUT INJURY! 

FOR PROPER PROTECTION OF HANDS, A PROTECTIVE 

GLOVE SHOULD BE USED WHEN OPERATING THIS 

EQUIPMENT AND DURING THE HANDLING OF BLADES. 

 

ALWAYS

 

DISCONNECT

 

THE

 

TOOL

 

FROM

 

THE

 

AIR

 

SUPPLY

 

PRIOR

 

TO

 

SERVICING. 

 

 

Models 880, 1880, 1400, 1500 and optional 505: 

 

These models are equipped with an adjustable depth gauge for setting a controlled product trim 
thickness.  The depth gauge can be adjusted for cuts up to ¼” thick.  A depth gauge setting 
device is also available.   

 

To adjust the depth:

 

 

 

Hold the handpiece with the blade facing downward. 

 

Loosen the depth gauge mounting screw(s). 

 

Adjust the depth gauge setting by sliding it up or down to the desired height.   

 

Retighten the depth gauge mounting screw(s). 

 

 

Depth Gauge Adjustment Range: 

 
 
 
 
 
 
 
 
 

 

 

 
 

           

Model 880 Whizard

®

 AirMax MACH 3

 

 

 

 

 

Model 1400 Whizard

®

 AirMax MACH 3 

 

 

Slide to Adjust 

Moving Up = Thicker Cut 

Moving Down = Thinner Cut 

Depth Gauge  
Mounting 
Screws

 

Depth Gauge  
Mounting 

Screws 

Содержание Whizard AirMax MACH 3
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды