manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 78

 

 Maintenance

 

 

5-34 

Maintenance 
Whizard

® 

AirMax MACH 3 Operating Instructions and 

Parts List 

Manual No.  188000   
September 1, 2009 

 

Assembly of TRIMVAC

®

 AMX Handpiece

 (Continued) 

 

Step 3:  Install Bearing: 

 

 

Push the handpiece bearing into the frame bore and align the bearing flat with the frame 
flat. 

 

The bearing should go in with minimal effort and not require pressing. 

 

Do not force the bearing in.  If the bearing does not go in easily, check frame and bearing 
for damage or build-up. 

 
 
 

 
 
 
 
 
 
 
 

 
 
 
 

Step 4:  Install Pinion: 
 

 

Insert the pinion into the bearing bore. 

 

The pinion should go in with minimal effort and 
not require pressing. 

 

Do not force the pinion into the bearing.  If the 
pinion does not go in easily, check the bearing 
and pinion for damage or build-up. 

 

The pinion should sit flush against the bearing.  
If it does not, rotate the pinion to seat it flush 
with the bearing. 

 

 

 

 

Align Flats 

Содержание Whizard AirMax MACH 3
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды