BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 109

Страница: 109 / 183

Maintenance

Manual No. 188000
September 1, 2009

Maintenance
Whizard

AirMax MACH 3 Operating Instructions and Parts

List

5-65

Valve and Hose Assembly Maintenance

Required Tools for Valve and Hose Assembly Maintenance

1 – 1/2” Open End Box Wrench
1 – 9/16” Open End Box Wrench

Inspection of Valve and Hose Assembly

Valve and Hose Assembly



Connect the valve and hose assembly to the
FRL at 90-100 psi.



If air leaks around the plug assembly,
replace the valve assembly.



If the valve body is dented, nicked, or
scratched, replace the valve assembly.



If air can be felt leaving the muffler, replace
the hose assembly.



If the exhaust hose is cut, torn, or nicked,
replace the exhaust hose.



If the muffler is dirty or clogged, replace
the muffler.

Valve

Body

Plug
Assembly

Exhaust

Hose

Muffler

Exhaust Hose

Содержание Whizard AirMax MACH 3
























































































































































































Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды