BETTCHER INDUSTRIES Whizard AirMax MACH 3 Скачать руководство пользователя страница 29

Страница: 29 / 183

Instructions for Operation

Manual No. 188000
September 1, 2009

Instructions for Operation
Whizard

AirMax MACH 3 Operating Instructions and Parts

List

4-5

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 2:



While holding the
Whizard

AirMax

MACH 3 frame, align
the pin in the power
unit with one of the
notches on the frame.



The frame is designed
with multiple notches
to allow the head to be
adjusted to the most
comfortable position
for the operator.



For the initial
adjustment position, the
short groove on the
power unit should be
facing up. See illustration at right.

Step 3:



Insert the attachment screw in
the frame.



Tighten the attachment screw

FIRMLY,

using the supplied

hex wrench.

NOTE:

Recommended torque of

115-140 lb-in (13-16 N-m).

Short
Groove

Notches

Frame

Power
Unit

Hex

Wrench

Frame

Attachment
Screw

Содержание Whizard AirMax MACH 3
























































































































































































Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard AirMax MACH 3, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard AirMax MACH 3

Отзывы:

Бренды по названию

Популярные бренды