bergmann ALPHA-PACK-BIN Скачать руководство пользователя страница 61

Страница: 61 / 98

12. Trouble - Shooting

12.

All maintenance and repair works may only be carried out by qualified personnel
with corresponding know how.
It is absolutely necessary to consider the safety instructions in Chapter 3.

Problem

Source

Solution

The machine cannot

1.1 No power available

Check supply voltage

be switched on

1.2 Plug faulty

Change plug

1.3 Isolator not switched

Switch on isolator (over the

plug)

1.4 Motor overload

Re-set motor overload

protection has tripped

(see fig. 1, pt. 1)

1.5 Defect fuse

Change fuse (see fig. 1, pt. 2)

1.6

EMERGENCY SHUTOFF

Release

EMERGENCY

button

locked

SHUTOFF

button

1.7 Switch contacts stuck

Check all contacts in control
panel

1.8 Float switch registering

Top up with hydraulic oil or

too little oil

carry out oil change
(see chapter 7)

1.9 Elektric motor defective

Replace motor (see fig. 3, pt. 1)

fig. 1

Содержание ALPHA-PACK-BIN



































































































Результаты поиска

Содержание ALPHA-PACK-BIN

Отзывы:

bergmann ALPHA-PACK-BIN, Руководство по эксплуатации, Страница: 61 / 98

Результаты поиска

Содержание ALPHA-PACK-BIN

Отзывы: