background image

Bennett Site Master Instruction Manual 

Safety Instructions 

 

IMPORTANT SAFETY INSTRUCTIONS 

For  safe  installation  of  this  equipment,  read  and  understand  all  dangers,  warnings,  cautionary,  and  important  information.  Save  these 
important safety instructions in a readily accessible location. Look for the following warnings throughout the manual:  

Red and White 

“DANGER” 

means: If you do not follow the instructions, severe injury or death will occur. 

Orange and Black 

“WARNING” 

means: If you do not follow the instructions, severe injury or death can occur. 

Yellow and Black 

“CAUTION” 

means: If you do not follow the instructions, damage can occur to the dispenser. 

Blue and White “

IMPORTANT” 

means: Helpful tips and other recommendations on equipment installation, usage, and maintenance 

should be observed. 

DANGER 

PELIGRO 

DANGER 

 

FIRE, EXPLOSION, INJURY, OR DEATH WILL OCCUR IF FUEL FILTERS ARE CHANGED BY UNTRAINED PERSONNEL. 
MAKE SURE, ONLY TRAINED PERSONNEL CHANGE FILTERS. 

 

TO PREVENT INJURY TO YOU FROM VEHICLES AND ONLOOKERS, ALWAYS PLACE A BARRIER AROUND THIS 
EQUIPMENT BEFORE PERFORMING SERVICE OR MAINTENANCE. 

 

GASOLINE IS FLAMMABLE. NO SMOKING OR OPEN FLAME. 

 

DISCONNECT ALL POWER AND RELIEVE PRESSURE TO THIS EQUIPMENT AND ASSOCIATED SUBMERGED 
PUMP(S) DURING INSTALLATION, SERVICE, OR ANY MAINTENANCE I.E., CHANGING FILTERS. 

WARNING 

ADVERTENCIA 

MISE EN GARDE 

 

You must have training in the installation, service, or maintenance of this equipment (dispenser, pump, site 
master, console, control box, payment terminal, or submerged pump) before working on it. Maintenance repairs 
must be done by authorized personnel only. Warranty work may only be performed by Bennett certified 
technicians. 

 

To prevent electric shock, keep the electrical parts of the Site Master dry. 

 

Electronic components are static sensitive. Use proper static precautions (e.g. static straps) before working on 
the equipment.  

 

The emergency shut-off valve (also called the fire valve, shear valve, or impact valve) must be closed when 
service or maintenance is performed on this equipment. 

 

You must have training in the operation and programming of this Site Master Payment Terminal before using it. 

READ THE OPERATORS MANUAL.

 

 

Make sure this equipment is correctly grounded. Failure to do will cause injury or damage equipment or 
improper operation. Improper grounding voids the warranty. 

 

Do not operate the equipment as a payment terminal unless it is completely assembled. 

CAUTION 

PRECAUCIÓN

 

MISE EN GARDE 

 

Do not drill holes in the Site Master. Holes can cause failure of the electronic equipment. 

THE 

WARRANTY WILL BECOME VOID.

 Use only adhesive backed sign mounting brackets

 

 

IMPORTANT 

IMPORTANTE

 

IMPORTANT 

 

All trained technicians must work in accordance to all requirements, standards, and guidelines specified by the 
suppliers Environmental Standards® Health, Safety, Security & Environment (HSSE) policies. 

Note: 

Bennett Pump 

highly recommends all technicians observe HSSE policies defined by the supplier. Bennett Pump does not impose 
any restrictions or additional requirements contained in Environmental Standards® Health, Safety, Security & 
Environment (HSSE) policies. 

 

 

!! READ AND UNDERSTAND ALL WARNING LABELS ATTACHED TO THE DISPENSER !! 

 

 

Содержание SITE MASTER EMV





























Отзывы: