Belden Miranda DENSITE 3+ FR1, Руководство пользователя

Страница: 31 / 65

17
Densité 3+ FR1
User Manual
Configuring the CPU-ETH2 Controller
This section introduces the operating features of the CPU-ETH2 controller, and describes
how to access and control them using:
• The iControl interface
• The local control panel and menu.
The local control panel must be used to configure the network settings for the controller.
Beyond that, the iControl interface is more comprehensive and easier to use, so it will be
used as the primary interface for purposes of describing the configuration process.
In each case, the menu path which must be navigated on the local control panel to access
the configuration item under discussion will also be given.
The following topics are covered:
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Status Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SNMP functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Data Restoration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Factory Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Time Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Network Configuration
The CPU-ETH2 card is shipped with the following settings for ETH 1:
IP address: 192.168.3.1
Subnet mask: 255.255.0.0
Gateway: 0.0.0.0
To control the frame using iControl in your network, you must reset the IP address. This can
only be done using the local control panel.
Preparation:
Obtain the IP address, Network Mask and Gateway values for this
controller in your network.
Note:
The menu function will timeout if there is no activity for 30 seconds,
so be prepared to enter your values efficiently.
To reset the IP address
1 Open the frame door to view the controller panel.
2 Click the Controller button on the panel.
The controller menu is shown on the display.
3 Click [–] until ETH1 OPTIONS appears in the display.
4 Click [SEL], then click [–] until IP ADDRESS appears in the display.
5 Click [SEL].
The current IP address is shown.