Beckman Coulter SW 32 Ti Скачать руководство пользователя страница 30

Страница: 30 / 38

LXL-TB-015BB

SW 32 Ti and SW 32.1 Ti Swinging-Bucket Rotors

Care and Maintenance

Frequently lubricate the bucket and cap mating surfaces with a thin, even coat of Spinkote
lubricant (306812).

Refer to Appendix A in

Rotors and Tubes

for the chemical resistances of rotor and accessory

materials.

•

Your Beckman Coulter representative provides contact with the Field Rotor Inspection
Program and the rotor repair center.

Cleaning

Wash the rotor and rotor components immediately if salts or other corrosive materials are used or if
spillage has occurred. Do not allow corrosive materials to dry on the rotor.

Under normal use, wash the rotor frequently (at least weekly) to prevent buildup of residues.

Wash the rotor buckets, O-rings, and caps in a mild detergent, such as Beckman Solution 555™,
that won’t damage the rotor.

Dilute the detergent 10 to 1 with water.

•

The Rotor Cleaning Kit contains two plastic-coated brushes and two quarts of Solution 555
(339555) for use with rotors and accessories.

Rinse the cleaned rotor and components with distilled water.

Air-dry the rotor and buckets upside down. Do not use acetone to dry the rotor.

Air-dry the rotor and lid upside down.

Do not use acetone to dry the rotor

Clean metal threads frequently to prevent buildup of residues and ensure adequate closure.

Use a brush and concentrated Solution 555.

Rinse and dry thoroughly, then lubricate lightly but evenly with Spinkote to coat all
threads.

Содержание SW 32 Ti







































Результаты поиска

Содержание SW 32 Ti

Отзывы:

Бренды по названию

Популярные бренды

Beckman Coulter SW 32 Ti, Инструкция по эксплуатации

Результаты поиска

Содержание SW 32 Ti

Отзывы:

Бренды по названию

Популярные бренды