manualshive.com logo in svg

Beckman Coulter SW 32 Ti, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter SW 32 Ti Скачать руководство пользователя страница 15

LXL-TB-015BB

7

SW 32 Ti and SW 32.1 Ti Swinging-Bucket Rotors

Preparation and Use  

Removal and Sample Recovery

CAUTION

If disassembly reveals evidence of leakage, you should assume that some fluid 
escaped the rotor. Apply appropriate decontamination procedures to the 
centrifuge and accessories.

1

Grasp the bucket cap tabs and lift up to remove the buckets.

 •

 (Buckets may be removed without removing the rotor body from the ultracentrifuge.)

2

Remove the bucket caps by twisting counterclockwise and lifting up. 

a.

Use a tube removal tool (361668) or hemostat to remove the spacers and tubes.

NOTE

If the conical-shaped adapters that support 

k

onical tubes are difficult to remove after 

centrifugation, an extractor tool (354468) is available to facilitate removal.

3

To remove the rotor from the centrifuge, lift the rotor straight up and off the drive hub. 

a.

Set the rotor on the rotor stand.

Tubes and Accessories

The SW 32 Ti rotor uses tubes and accessories listed in 

Table 1

; the SW 32.1 Ti rotor uses tubes and 

accessories listed in 

Table 2

. Be sure to use only those items listed, and to observe the maximum 

speed limits shown. Refer to Appendix A in 

Rotors and Tubes

 for information on the chemical 

resistances of tube and accessory materials.

1.

Extractor Tool (354468)

While pressing the rubber tip against 
the adapter wall, pull the tube and 
adapter up and out of the cavity.

1

Содержание SW 32 Ti







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды