manualshive.com logo in svg

Beckman Coulter SW 32 Ti, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter SW 32 Ti Скачать руководство пользователя страница 11

LXL-TB-015BB

3

SW 32 Ti and SW 32.1 Ti Swinging-Bucket Rotors

Description  

Description

These Beckman Coulter rotors have been manufactured in an ISO 9001 or 13485 facility for use with the 
specified Beckman Coulter ultracentrifuges

.

The SW 32 Ti and SW 32.1 Ti are swinging bucket rotors designed to centrifuge up to six tubes each. 
Used in Beckman Coulter class H, R, and S preparative ultracentrifuges, these rotors develop 
centrifugal forces for the separation of subcellular particles and viruses in density gradients. The 
rotors have a common rotor body with buckets that can be used interchangeably (see

 

Rotor 

Preparation

). Bucket and rotor body positions are numbered for operator convenience. 

The rotor body and buckets are made of titanium, finished with polyurethane paint. Bucket caps are 
made of aluminum, anodized for corrosion resistance. Each bucket and cap assembly sets into 
grooves in the rotor body. O-rings, made of Buna N rubber, between each bucket and bucket cap 
maintain atmospheric pressure inside the buckets during centrifugation. 

For overspeed protection, a Beckman Coulter ultracentrifuge equipped with a photoelectric 
detector will monitor the overspeed disk on the rotor bottom and shut down the run if a speed 
exceeding the maximum allowable run speed is detected.

See the Warranty at the back of this manual for warranty information.

1.

Black Cap

2.

O-ring (812715)

3.

Bucket (SW 32 Ti)

4.

Rotor

5.

Overspeed Disk (335456)

1

5

4

3

2

Содержание SW 32 Ti







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды