manualshive.com logo in svg

Beckman Coulter SW 32 Ti, Инструкция по эксплуатации

Поделиться
Скачать
Beckman Coulter SW 32 Ti Скачать руководство пользователя страница 3

LXL-TB-015BB

iii

Safety Notice

Read all product manuals and consult with Beckman Coulter-trained personnel before attempting 
to use this equipment. Do not attempt to perform any procedure before carefully reading all 
instructions. Always follow product labeling and manufacturer’s recommendations. If in doubt as 
to how to proceed in any situation, contact your Beckman Coulter Representative.

This safety notice summarizes information basic to the safe use of the rotors described in this 
manual. The international symbol displayed to the left is a reminder to the user that all safety 
instructions should be read and understood before operation or maintenance of this equipment is 
attempted. When you see the symbol on other pages of this publication, pay special attention to the 
safety information presented. Observance of safety precautions will also help to avoid actions 
that could damage or adversely affect the performance of the rotor. These rotors were developed, 
manufactured, and tested for safety and reliability as part of a Beckman Coulter ultracentrifuge/
rotor system. Their safety or reliability cannot be assured if used in an ultracentrifuge not of 
Beckman Coulter’s manufacture or in a Beckman Coulter ultracentrifuge that has been modified 
without Beckman Coulter’s approval.

Alerts for Danger, Warning, Caution, and Note

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, 
will result in death or serious injury. 

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, 
could result in death or serious injury. 

CAUTION

CAUTION indicates a potentially hazardous situation, which, if not avoided, 
may result in minor or moderate injury. It may also be used to alert against unsafe 
practices.

NOTE

NOTE is used to call attention to notable information that should be followed during installation, use, 

or servicing of this equipment.

Safety Information for the SW 32 Ti and SW 32.1 Ti Rotors

Handle body fluids with care because they can transmit disease. No known test offers complete 
assurance that such fluids are free of micro-organisms. Some of the most virulent—Hepatitis (B and 
C) viruses, HIV (I–V), atypical mycobacteria, and certain systemic fungi—further emphasize the 
need for aerosol protection. Handle other infectious samples according to good laboratory 

!

Содержание SW 32 Ti







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды