Beckhoff CX-B510 Series Скачать руководство пользователя страница 65

Страница: 65 / 81

Parameterization and commissioning

CXxxxx-M510/B510

Version: 1.0

5.3.7

Setting the transmission type

The transmission type determines how the process data objects are transferred. The transmission type for
the RxPDOs and TxPDOs is set on the PDO tab.

The available transmission types are: acyclic synchronous, cyclic synchronous, and asynchronous.

Transmission type:

Acyclic Synchronous

Cyclic Synchronous

Asynchronous

Name in TwinCAT:

(acyc, sync)

(cyc, sync)

(async)

Prerequisites for this step:

• A CANopen slave with process data objects (PDO) added in TwinCAT

Specify the transmission type as follows:

1. In the tree view, left-click on a process data object (PDO).

2. Click on the

PDO

tab.

3. Select the required transmission type under

Trans. Type

You have successfully specified a transmission type for a process data object. The transmission types
for the remaining process data objects are specified in the same way.
Next, you can create a PLC project for the CANopen slave.

Содержание CX-B510 Series


















































































Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды

Beckhoff CX-B510 Series, Руководство пользователя

Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды