Beckhoff CX-B510 Series Скачать руководство пользователя страница 56

Страница: 56 / 81

Parameterization and commissioning

CXxxxx-M510/B510

Version: 1.0

5.2.11

Adding a CANopen master

The CANopen master is added with the TwinCAT System Manager, like the other devices. The attached
master can then be used to find all connected slaves. The following section illustrates how to add a
CANopen master in TwinCAT.

Prerequisites for this step:

• TwinCAT must be in Config mode.

• A selected target system (in this sample it is the Embedded PC CX2020-M510)

Add a CANopen device as follows:

1. Start the System Manager.

2. In the tree view on the left, right-click on

I/O Devices

3. In the context menu click on

Scan Devices

4. Select the devices you want to use and confirm the selection with

5. Confirm the request with Yes, in order to look for boxes.

The

Select Baud Rate

window appears.

6. Under Baud Rate select the appropriate baud rate for the CANopen master.

Содержание CX-B510 Series


















































































Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды

Beckhoff CX-B510 Series, Руководство пользователя

Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды